Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ADE7005AYW > Instructions

ADE7005AYW Admiral Dryer - Instructions

All installation instructions for ADE7005AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ADE7005AYW
331-345 of 512
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The indicator is 180 degrees out of alignment

  • Customer: maurice from colorado springs, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Magic marker

Male end of door catch broke

  • Customer: George from Hamden, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First, I replaced the male end which was just two screws and simple replacement of pushing the fastener into the door frame. When finished I noticed the female end was damaged as well. Glad the female part came as well. This required taken off the front trim around the door (four screws - 2 each side) and then the door. The installing of the female end was easy with a little push. The damaged female end was already hanging out so easy to grab and remove. Otherwise I would have had to remove the front panel. Note You need to put the door trim back on before reattaching the door.

screeching noises

  • Customer: Theodore from San Francisco, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I followed the steps in the partselect videos and it was pretty easy. A small adjustable wrench was a lot easier to use than the needle nose pliers recommended in the video. The metal bearing inside the wheel on the idler lever turned out to be the main cause of the problem. It had worn a lot and more on one side than the other so the wheel was wobbling back and forth. However, the belt was clearly deteriorating as well, so I'm glad I replaced it. The glides were thin but serviceable, but also very easy to replace. I also replaced the two wheels in the back of the machine that support the drum. Probably did not need to do that.

Latch was broken so door wouldn't close

  • Customer: Doug from Kearney, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This was real easy just slid the latch in front panel and attached to latch assembly to the door. The repair was about 45 seconds.

dryer would not start

  • Customer: Steven from Webster, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Began by unplugging power then removed the two screws from bottom access panel removed panel. Used a putty knife to push the release clips hold the top panel removed the two screws holding the front door and housing noted the three wires for the door switch removed those. Released the tension on the belt at the idler pulley lifted the drum assembly from the dryer. Tested the high limit fuse assembly with a volt ohm meter found no continuity indicating the fuse was blown. After reading the many other reviews I also test the high limit thermostat and found that it was not working as it should order bout parts and replaced all in reverse order plugged the unit back in and now have a working dryer.

Drum Making Loud Noise

  • Customer: OFELIO from EGG HARBOR TOWNSHIP, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed front lower panel bolts ,top panel bolts and removed panels. Then slid putty knife between top cover on each end and swung top cover back. Released tension off tub tensioner n removed tub . Removed snap ring n rollers n replaced with new. Insalled tub n belt n panels.

bad grinding noise

  • Customer: Perry from Elk Ridge, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Just followed the very helpful video. It was a snap - no hitches at all. Thanks a million for the help videos. So much cheaper than a repairman.

Old lint filter fell apart

  • Customer: Marcia K. from Bryan, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
For some time I have been using a lint filter that was bent and cracked. Recently it got much worse. I finally had had enough!. Went on line,found you, ordered what I needed, and TAA! DAA! In a few short days, hassle free clothes drying! Thank You!

Constant Screeching

  • Customer: Elizabeth from New city, NY
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I search on the Internet to troubleshoot. I began to disassemble the unit with information I gathered from other websites. I checked the idler lever and knew indeed that was the screeching culprit. Once, I figured out the parts I would need to do a thorough job (idler lever, 2drum support rollers, multi-rib belt), I searched for parts and came upon partselect.com. I got more thorough review via the partselect videos on how to replace everything and put it back together. If I knew about this site and the detailed videos it provides for each part I ordered, I would have saved myself at least 1.5 hours from the reasearch and disassembling time. I followed the videos and only asked for backup help when I was putting the new belt around the idler lever. Hearing the dryer run again without the screeching was such a relief!

the plastic latch broke

  • Customer: greg from phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
im a car mecanic it was easy

Loud squeaky sound, screeching, rumbling

  • Customer: Douglas from Holly Springs, NC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Followed the instructive videos on this site. Purchased more repair items than I thought I might need since I wasn't sure what I'd find. Turned out the drum support rollers were fine so I didn't remove them. Problem was a failed bearing on the idler pulley lever. Replaced that and the belt (for good measure). Returned what parts I didn't use. Thanks PartSelect!!

idler lever wheel broke and belt worn(little)

  • Customer: Duane from Jones, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
I did repair as video had shown. it was a challenge I prefer not to persue, with having no professional mechanical background. The repair was a sucess and with only a 60.00 charge for parts and 1 day shipping I would do it again.I have the origonal belt for backup if new one breaks in future.Duane

made high pitch noises

  • Customer: Ricardo from Lewisville, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Just follow the how to videos on part select website and you`ll have no problems.

Blown heating element

  • Customer: Selena from Westerville, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Found the part with ease on your site. Shipped out regular service & received within 3 days! Awesome. Directions were easy to follow... easy to install. Would recommend to all!

Its not a problem, simply old and needed to be replaced to make the dryer more efficient.

  • Customer: Mohammed from Beltsville, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
No repair at all. Simply pulled out the old filter and slipped in the new one.
All Instructions for the ADE7005AYW
331-345 of 512