ABR2227VES10 Amana Refrigerator - Instructions

Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)

Just replaced old with new. The glass shelf was good so just moved it to the new pieces. Everything fit perfectly, thank you.

Old gasket pulled of easily with no tools. New gasket was placed on floor and heated with blow dryer to straighten. Then installed new gasket by pressing in with my hands. Noticed that the old gasket was hard and not flexible. All was great. Fit perfectly. No frost after a week. Happy.

The parts were very easy to replace, however I am still without ice and cannot figure out why. I have ohm tested the contol unit and everything works fine, I am able to jump it and turn on the motor and water fill valve. Any suggestions?...

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Total time 10 minutes. 9 minutes to clear out the food and 1 minute to install the part. Installation was self evident and could have been done blindfolded. Part just snapped in.

Snapped in new part

Very easy to order from parts select. Took seconds to replace.

Very easily removed top shel glass above crisper--removed old rail by lifting up--and place new one in slots provided---simple!! Part was delivered in less than 3 days-------very fast and cheap !!!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

remove parts that were not need installed water valve , ice maker unit and hooked up water supply tested and it works fine. got the parts really quick Thank You

Snapped on the new toe grille.

i just took the prts apart and replaced with new part really easy and saved $185.00 easy as pie

I first removed the icemaker pump and filler tube fron the back of the refrigerator by using an adjustable wrench and pliers. (very simple connection) I went ahead and replaced both items at that time.

Next I opened the bottom freezer and removed the top wire tray and ice container. I removed the bottom nut from the ice maker, pulled the electrical plug lose from the freezer connection. I then just lifted the ice maker upward and off the two screws on the side wall and out it came!

I had a little trouble with the filler tube as it came into the freezer. I had to go back and forth to the back of the refrigerator and freezer a couple of times adjusting the tube, so it woiuld clear the inside freezer wall.

This was a very minor problem. I feel like if I had followed the instructions and made sure the tube came through before attaching the icemaker it would have worked like a charm!

What I really liked, was everything was in the box for the job.