All Installation Instructions for Amana Refrigerator AB2225PEKB12

The center crisper rail for the crisper pans broke and one of the bins ended up cracking

I removed the crisper pans, installed the new rail and then installed the new bins. Very easily done--I was finished in 10 minutes

Parts Used:

Refrigerator Crisper Pan

Refrigerator Center Crisper Drawer Slide Rail - White

Bryan from Laurel, MD
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker bucket missing

Needed ice maker bucket for extra fridge. Part came the next day, and worked perfectly.

Parts Used:

Ice Bucket

Susan from Edgerton, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Difficulty removing old switch.

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.

Parts Used:

Door Switch

Ronald from HUNTINGTN BCH, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Stead flow of water from under the refrigerator

Unplugged and disconnected the water supply.Disconnected the water line coming from the filter and cut about 1/8 inch off to square it off.
Unscrewed panel to expose inlet valve. With a marker I noted where the lines need to go back to. Disconnected the other two lines and made fresh straight cuts with a utility knife. Disconnected both plugs from the old inlet. The yellow one was difficult to get off, so I carefuly used a screw driver. Be careful, you don't want to break the plug. Reinstalled the new inlet. make sure that you push all of the lines in the valve so that they are completely seated. Make electrical connections. Secure valve to the panel. The water line from the filter should be the last line that you connect. Put screws back in the panel.
Plug in and turn on water supply. Fill up a gallon container from water dispenser. Check for leaks. Let the ice machine fill up. Check for leaks. Place back panel back on and secure. GOOD LUCK!

Parts Used:

Refrigerator Dual Water Inlet Valve

Victor R. from BROOKLYN, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

part leaking water at joint

remove rear plate on refrigerator and remove two screws holding unit to plate. Cut the supply tube and the tube to ice maker and water spout. insert the existing tubes back into new unit and replace back on plate and then plate to refrigerator. That SIMPLE

Parts Used:

Refrigerator Dual Water Inlet Valve

Scott from ACWORTH, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

I had no problem

Just take the crisper out and just put it in the hall access

Parts Used:

Crisper Drawer Cover Support

DIANE from WEST PALM BCH, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Clean the glass and asked my wife to install the glass. She is less likely to brake the glass

Removed the plastic frame, washed the frame and fridge, set new glass into the frame.

Parts Used:

Refrigerator Crisper Glass

Dan from WATERVILLE, MN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

Parts Used:

Door Switch

John from AUBURN, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Water in door valve was leaking

Removed rear access removed valve mount turned off water supply Unplugged out of the wall plug removed the two electric plugs removed the three water lines installed the new valve in reverse order, check for water leaks worked perfect

Parts Used:

Refrigerator Dual Water Inlet Valve

Richard from Hammon, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

New Ice maker was install but technician failed to transfer arm off old ice maker and put on new one..

Work was done by service tech. I ordered the arm for my mom to save time when tech came back to do the job correctly.

Parts Used:

Ice Maker Shutoff Arm

Royal from RICHMOND, VA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

BOTH THE LADDER HOOKS, AND THE CRISPER PARTS WERE BROKEN

SIMPLY REPLACED THEM

Parts Used:

Refrigerator Crisper Pan

Crisper Drawer Cover Support

THOMAS from JOLIET, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Rail snapped

Followed video

Parts Used:

Refrigerator Center Crisper Drawer Slide Rail - White

Arthur from WYNNEWOOD, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Water line feeding ice maker was not producing ice

Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.

Parts Used: