91193211990 Kenmore Range - Instructions

Real happy on how fast the new part came.
1.Pulled oven away from wall and unplugged the unit & removed baking racks.
2.Removed the back wire cover behind the oven (3 screws).
3.Used the nutdriver to carefully remove the two holding screws inside the oven. Then I pulled the element towards me to expose the wires.
4. Using the pliers, I disconnected the element from the wires.
5. Using my son's help, I had him push the new element leads into the holes in the back while I connected the leads to the wires behind the oven.
6. Replace the two element retaining screws inside the oven.
7. Replaced the rear panel with the 3 screws.
8. Put the oven back in place and plugged it in. The oven worked perfectly!

I turned off the breaker for the oven. I used a electric drill with a 1/4 in socket to unscrew the two bolts inside the bottom of the oven. Then I pulled
out the heating element and slid off one connector and attached it to the new element. Then I slid off the other connector and attached it to the new element. Then I screwed the bolts back. I turned the breaker back on and it worked great.

Turn off circuit breaker.
Lockout (LOTO) circuit breaker.
Pull stove away from wall to access the rear of range.
Remove seven (7) screws from rear cover with nutdriver / screwdriver.
Carefully, disconnect stake-on terminals (wires) from element (may need to use needle nose pliers).
Open oven, remove racks.
Remove two (2) screws holding element in place with nutdriver.
Remove old broken element.
Insert new element. Fasten with screws previously removed. Close oven door. Go to rear of unit.
Reconnect wires to element. Make sure insulation seals around the element.
Inspect for any other damage; repair as may be required.
Replace cover panel and fasten with the seven screws previously removed.

Does not hurt to vacuum and clean the area stove, too.
Push stove back into position.
Remove LOTO and turn on circuit breaker (power)

Turn oven on to highest temp to bake off any contaminates on element. Turn OFF. Let cool. Replace racks a/r. Close oven door.

Invite the pretty girl next door to come over to bake something.... OK, this part is optional.

Replacement was extremely easy. The new part fit perfectly and installed very easily without tools. Also, I received the part within a few days

Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel

I downloaded the installaion manual from the web for this model. First htings first, I located the circuit breaker for the oven and turned it off. Removed the lower trim piece from the bottom, next lifted the oven door off its hinges and set it to the side. I then wrapped a couple of small towels around the hinges for the door as per the manual (the hinges can pinch a finger). I then removed the four screws which secured the oven into the cabinet. Next I slid the oven forward allowing me access to the rear. I removed the pieces from the rear to gain access to the sensors connector, and unpl;ugged the sensor. Went around to the front and unscrewed the 2 screws securing the sensor and removed it. I then installed the new sensor, replaced the rear covers, slid the oven back into the cabinet, secured the four screws, snapped on the lower trim, remounted the oven door, and turned the breaker on. Oven working fine now.

First, I got my husband and let him know that the part was in (really easy), then I sat back and watched as he pulled the oven from the wall, unplugged it and lifted the stove top (so far, I haven't broken a sweat)! I then peeped up under the top as he removed a scew from the element and then several screws from the back panel, trace the wire to the needed element, and reconnect the new element (haven't broken a nail yet)! He then secured the element back on its mount, let down the top and plugged the oven back in, checked for accuracy...mission accomplished! This was the easiest repair I've ever done!

Took off oven door and removed racks. Removed the cover on the back side (5 screws removed with nut driver) Pulled sensor out the front side of the oven. Threaded the new sensor through and put all back together.

Yeah, so I didn't read the manual the first time we ran the self-clean cycle on the oven. Something about taking the racks out. So these were my little reminder to never do that again. The old racks came out; the new ones went in. Ten seconds. On to the next embarrassment...

the chief of the house(not me) did not let the oven finish self cleaning process and that's why this happend.So for everybody - let it finish you'll get no trouble.But repair itself was easy.1-open the oven and take a racks out; 2-unscrew a support of the element on back wall(2 screws);3pull of the wall and unscrew back panel(5screws);4-unplug connectors and pull the element out of the oven.5-installation is the same but backward 4 to 1.It took me...think less then 4 minutes (I went for a beer).DIY and U save a tons.And BTW those guys from Part Select - excelent service.I'm glad that I found a website like that.It's all ready in my favorites.Thanx guys for quick and very good service.It came what I order and it came in 2(two)days.Keep in touch

The heating element in my electric oven cracked, I had something boil over onto the element, cracking it to the point of it sparking. First time I had ever seen this before. The appliance repair shop was going to charge me a small fortune to fix this so I ordered the part online, which it was 10.00 cheaper from here than from any other site. It got to me quickly and took me less than 15 minutes to repair and everything works great. All I had to do was unbolt 2 screws with a ratchet, unplug the element, plug in the new one, and bolt it back up and I was done!

Removed the broken socket, and replaced with new one.

When we moved into our new home I discovered that the oven that came with the home did not have any racks in it. I ordered these racks because they said they were compatible with Hotpoint ovens. However, when the racks arrived they were just a tad too wide to easily slide in the oven. With a bit of force my husband was able to shove the racks in. Luckily I don't cook enough to care if they are moved again because I don't think they'll come out easily.

Removed the 2 screws on plate. Pulled wires forward. Simply detached slide on connecters and inserted new element. Pushed back and installed plate. Dont forget to unplug the 220 volt. Though open can ground wires.

took 2 screws out of the element, then too the back off pluged in the element replaced two screws done