All Installation Instructions for Kenmore Range 79090910403

Burner wouldn't stay hot.

I pulled out the old element and the new one just plugged right in.

Parts Used:

Surface Element - 8 Inch - 220V

Billy from Lovelady, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Oven would kick off after preheating to temp.

Sensor very accessible. Pull off the back panel, disconect the sensor and slide out from back of oven. The original plug was cut off the sensor, as well as the new one to get the proper connector type on the new sensor. Soldered and heat shrink, and presto we had our new sensor ready for install. Install was about 5 minutes which included putting the back panel on the range. Pretty easy and works like new. Total time for project was about 20 minutes.

Parts Used:

Oven Temperature Sensor

Mary from Castle Rock, CO
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

12 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Enement was blew out.

I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.

Parts Used:

Surface Element - 6 Inch

Chhabildas from Charlotte, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

10 of 13 people found this instruction helpful.

Was this instruction helpful to you?

replacement burner

Just a replacement burner for my stove. No tools needed. Thank you for such a speedy delivery

Parts Used:

Surface Element - 8 Inch - 220V

Donna from Westfield, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 15 people found this instruction helpful.

Was this instruction helpful to you?

broil element was bad.

It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

Parts Used:

Broil Element

William from Fort Myers, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Socket set

8 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Oven light stayed on & smelled like electrical burning.

Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

Parts Used:

Oven Door Light Switch

Vincent from Brunswick, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

16 of 35 people found this instruction helpful.

Was this instruction helpful to you?

Oven light bulb went dark; it needed replacing

Twisted replacement bulb into place easily. Let there be light!

Parts Used:

Light Bulb

Lise from CEDAR GROVE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

10 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Bottom elerment burnt into

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

Parts Used:

Broil Element

Danny from Gaffney, SC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

8 of 11 people found this instruction helpful.

Was this instruction helpful to you?

broken lens over oven light

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

Parts Used:

LENS

Leslie from Warsaw, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 22 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator Light bulb went out

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Parts Used:

Light Bulb

ANGELA from MEBANE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Aluminum foil baked on surface

Took out 2 screws, removed panel.
When you put the panel in don’t push it tight to the front or the screws won’t align. Just place in gently and the screws will align

Parts Used:

Bottom Panel

Cindy from RHINELANDER, WI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Rusted leveling foot

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

Parts Used:

Leveling Leg Assembly

Melinda from Three Rivers, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)

6 of 9 people found this instruction helpful.

Was this instruction helpful to you?

While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Parts Used:

LENS