7635A Norge Dryer - Instructions

Just slid the new filter in.

Remove broken lint filter, stick in new filter. Couldn't be easier.

DISCONNECT THE POWER. Double check the dryer is unplugged. Use a putty knife to free the latches holding the top of the dryer in place. Lift up the top of the dryer and secure it in place (be sure it's safely held open and won't come crashing down onto yourself as you work). Remove the two screws on the inside and near the top of the dryer, which hold the front and side panels. Gently lift up on the front panel (it may help to open the dryer door to get a better grip). Once free from the bottom clips, carefully rotate the front panel so that the door sensor wires are not strained. Once the front panel is out of the way, grab the drum and firmly lift it up and away from the back. (The drum has rollers and ridges at the rear and you'll need to pull the drum out of its "track"). Slide the new belt around the drum and position the drum about halfway inside the dryer. Loop the belt around the motor, but not the tensioner, (it will be easier to install the drum if you wait to tension the belt). With the belt around the motor, gently slide the drum back keeping the belt around the motor pulley. Press and guide the drum back onto the rollers at the rear. Check the belt is positioned correctly around the drum and motor. Reach back from the front and loop the belt around the tensioner. Rotate the drum by hand and make sure the belt is aligned and the drum spins smoothly. Position the front panel and slide it onto the lower clips. Install the screws being very careful not to drop them into the abyss... Close the lid and plug in the power.

Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.

Removed broken filter, used screwdriver to clear out some old lint in the intake and inserted new filter. New filter fits and works as described.

Buy the part the site provide a video on how to do it and was very helpful thanks

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.

I tilted the unit back enough to scew the new legs into the threaded holes.

I pulled the old one off and put the new one on. It took about 3 minutes because I also replaced the old lint filter.

First unplug the machine and turn off the gas. Then, I pried the top up (2 clamps on front, 2 screws to the lint screen). Then I removed 2 5/16 nuts that fastened front panel to sides. I held the drum and pried the front panel back while my wife slipped the new belt around the drum. Then, I buttoned everything back up in reverse order, removed the kick panel, threaded the belt through the tensioner pulley and around the motor shaft. It's really that easy. PartSelect.com makes it simple with quick, accurate service.

Removed the two screws at the back that hold the top of the dryer. Then I pried off the top at the front by inserting a screwdriver into the front to remove the top from the clips. Then I tilted up the top like a car hood.

I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.

While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.

Then I replaced all the parts in reverse order, plugged it in and had a working dryer!

I pried the top of the dryer with a screw driver and then lifted the top of the dryer, I then removed the two screws "with a nutdriver" that held the door in place and then removed the door and drum. I then got the new belt and placed the belt over the drum and positioned the belt through the idler arm and then on the motor pulley. I had to hold the door and drum to lock the bottom of the dryer door to the dryer and then made sure the rear drum seal was in place and the belt did not slip off the motor pulley

It was easy to remove the lint trap first, then the front dryer panel. The drum easily was removed and installing the new belt was a little tricky because the belt had to be mounted onto pulley while holding the drum in place. I had a little help from a friend to help me stabilize the drum as I placed the new belt. Once on, it was easy to re-install parts in reverse and have dryer working again.

The dryer was not difficult to repair. The diagram that came with the belt made the repair easy. The repair part came in a very timely manner.