74403 - Instructions

unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!

Very easy just had to pull the wire up that holds it secure.

Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven

I followed the instructions from the lady taking my order she talked me through the steps

Followed instructions on website. Went perfectly.

Used this an old (maybe a 2007?) Briggs and Stratton 17.5 ho engine.This fan wasn’t an exact replica of the old one. But the bolt holes were in the right spot and it was the right size. Had to drill out the little dimples for the bolts and the fan guard that goes on top to stop debris didn’t screw directly into the fan like the old one. But I was able to attach the guard to the engine cover/piece that houses the air filter with a plastic bracket/retainer that was already on the engine. Overall, easy install and fit just fine once I determined how I wanted to attach the fan guard

Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.

1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.

First we replaced the wiring harness because a multi-meter said it wasn’t getting power. That was only partially true. The wiring harness was burned looking so we just kept it instead of sending it back. When the spark module got here the burner caps were removed and then the wires were noted where they went on the module and then the power and gas were turned off. The spark module was removed and then the stove was tested and we were back in business.

Had to remove oven door due to cabinetry. Removed screws holding unit to back wall. Pulled unit forward to release unit from front roof and expose wire connections to unit. Trick #1--get both hands into oven to to remove wires from unit. Front hanger for unit was different than old unit. Had to remove front hanger from both units. Hanger from old unit had to be sqeezed onto new unit in the unit in the proper location to fit into the roof stirrup to hang the unit. Now, two arms and hands into the back of the oven to reconnect the wires to the element. Slide the old support into the stirrup and screw to back wall. Result, the back wall plate of the new element partially covered the edge of the light cover which will be a challenge to replace the bulb.

We turned off the power, took out the element, installed new element.

ordered an oven rack, stuck it in the oven --- how easy is that?

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.

We pulled the stove out from its slot in our island. We unplugged it and unhooked the gas line so we could get behind it easily. We then took off the back (using screwdriver) to get to the connectors for the element. We unhooked the connectors from the old element. Then we took off the plate inside the back of the oven (using screwdriver)and gently pulled the old element out. We seated the new element in the oven and then hooked it up in the back and put it all back together again. It worked perfectly! The hardest part was cleaning the dirty floor under where the oven had been for 7 years!