6LSR5132AW2 Whirlpool Washer - Instructions

Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!

After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!

Followed the videos on the website. But had to order parts twice because it wasn't the springs it was the plastic bushings the tub sits on that caused the wobble. No big deal though. All told it was still far less expansive than a new machine.

just like video showed really helpfull

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

Unplug electrical cord, disconnect water inlet hoses and drain line at rear panel. Move washer to garage or larger work area if necessary. Disconnect control panel from top of washer cabinet by removing the two screws at the front corners of the control panel. (The control panel can now be flipped up and back when you are ready to remove the cabinet assembly.) Disconnect the rear panel from cabinet assembly by removing attaching screws at bottom of rear panel (and along the vertical edges if any screws are installed there). Either slightly lift the rear panel up off of the two clip brackets that attach it to the rear top edge of the cabinet assembly, or if need be remove the clips from the cabinet slots. With the rear panel loose, slide the control panel assembly slightly towards the rear and up to disengage it from the cabinet slots, then tip it up and back, away from the cabinet. The cabinet assembly (with top attached) can now be tipped forward and away from washer to expose the internal workings. (It may be necessary to support the rear panel and/or control panel.) The water pump is attached to the front of the motor by two spring clips. Disconnect the two water lines from the pump, then remove the two spring clips. Pull the pump forward off of the shaft extending out of the motor. Install the new pump, then assemble the washer in reverse order. (I was unsure where the leak originated on my washer so I completely removed the rear panel which entailed disconnecting from it the electrical cord fitting, drain and input water fixtures and various other brackets. Pump replacement can be accomplished without completely removing the back panel.)

I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!

Unplug the washing machine. Remove screws from the washing machine control console and lift it up. Then removed medal springs that connect the back of the washing machine to the cabinet. Then removed the cabinet about 3/4 of an inch forward. Then unscrew the old Lid Switch Assembly and put in the new one. Then slide the cabinet back on the washer and screw it back together and replug it and it worked.

simple and easy . Just tipped the machine back, pump was right there in the front.
Hardest part was getting the old pump off the shaft. I used a small block of wood & a large screwdrive to pry it loose (gently).

After it came off I filed off some corroded spots on the shaft before slidding on the new one. then its slid on easy,
Snapped on the clips , clamped on the hoses, Done, Momma's Happy, I'am Happy

Ordering was easy, Shipping was fast.
I will use you again.

There was no repair process. I just removed the old part by lifting it, and I inserted the new part. I was just happy that I was able to replace the part without having to call a repair person.

Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off without unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.

The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.

It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.