66514799N511 Kenmore Dishwasher - Instructions

Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

Turned off power to the dishwasher. Removed the front panel via the screws on the inner wall of the door. Lifted and pulled out the front panel. Disconnected cable connections to fully remove the front panel. Pressed down on the latches to the left and right side of the door latch. Pulled out the door latch. Put in new door latch until it clicked into place. Reattached cable connections. Put the front panel back on with the screws. Turned back on power to the dishwasher.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Gently pull the old door seal out of it's track observing the orientation of the seal and the amount of extra seal at the ends of the seal grove/track..
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.

The rubber door seal was easy after watching the video. I key point however is that you do have to stretch the seal just a little bit. The video says not to. If you don't like I didn't originally, the seal will only extend from one side to the other without about an inch excess that folds on the bottom of each side. The door still leaked a little without the excess folded on each side. I did one side at a time and pulled out the new seal along the side before curving to the top, and just stretch it slightly to allow the excess. This stopped the leak.

The lower door seal was ok to do. The most important step there is to remember how the front door panel is installed. Taking pictures before and during removal may help. It is awkward to do by yourself, but can be done. I found that putting a balled-up towel at the top of the door helps when trying to reinstall the front panel.

First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.

Two of the four small nylon/plastic tabs on the adjusters that support the top rack on the rack slides, broke off (one on each side).

Before the new parts arrived, I printed the limited (but definitely helpful) instructions that were available and familiarized myself with the adjuster assemblies.

As practice, I took one adjuster assembly apart making notes of any "gotchas." The main gotcha I found is that the nylon/plastic parts are easy to break (obviously) as prying is involved during removal and replacement. It took me about 20 to 25 minutes to take one side apart and about 10 minutes to put it back together again.

When the new parts arrived, I was able to do the first side in about 10 minutes (removal and replacement), and the second side in about 5 minutes, all because I had printed the instructions, familiarized myself, and practiced. I hope this helps.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Popped damaged/worn wheel assembly off, snapped new ones in. Easy peasy

Removed old housing parts and replaced them with the new parts I ordered. Very easy

I did a Youtube search and discovered there were a couple that showed the replacement in detail. I watch the entire process once and then had my laptop beside the upper rack and paused the video after each step. That worked well

I read how other people had the same problem, I checked everything that could possibly cause this. I then believed I knew what was wrong. I ordered a new arm. It was unbelievable how easy it was to replace.it. It took less time than a minute. . Turn the nut holding the arm counter clockwise to remove the arm. To replace turn the nut clockwise I now have a working dishwasher. It is not necessary to remove the dish rack.