66513929K014 Kenmore Dishwasher - Instructions

Turned off power to dishwasher.
Removed screws from dishwasher retaining clips.
Pulled out dishwasher.
Removed broken rope.
Installed replacement and put everything back together.
Very easy repair. The spring is very strong and extra hand can be helpful, but not required.

Thank you for letting me share my repair experience with you.
I removed the two screws that hold the diswasher to the wooden cabinet. Lowered the leveling adjustment screws on bottom of unit, then slid out the diswasher from inside the cabinet.
Then ordered the new lanyard. Waited one week day and the order arrived via mail. It has two lanyars and new rotating pulley assemblies for both sides of the door. I loosened the bottom screw on the old pully assembly and refitted the new pulleys in same location. (very easy). I then refitted spring to back of unit (with blue line toward front), then fitted the lanyard to the spring. Pulled lanyard thru the pulley. Had to have nice wife connect the other side of the lanyard to the post as I extended the spring on the side of the unit. We completed same steps on other side of the unit. After completing the door lanyard repair, I slid the dishwasher in the cabinet, re-leveled the unit with the front adjustment screw, then incerted the cabinet screws into the wooden cabinet. I feel this was quite a savings to us. Thanks to nice individuals on the internet and partselect.com, who provided excellent service to me....and my family. I also can see the end result of my effort, which is a nice feeling.
Thank you.

After pulling the dishwasher out of the cabinet (2 screws held brackets to the underside of the counter - accessible when the door is open), I removed the broken link pieces, re-attached the springs and routed the link line around the pulleys. No need to re-set the spring tension as it was adjusted properly.

Was able to download a PDF manual from Sears for the dishwasher, so had the necessary information in the event adjustments were necessary.

I bought spare links as the dishwasher was less than 3 years old, and I expect them to fail again.

Removed 2 screws that held unit under counter. Slid diswasher out about half way; reattached metal spring in back and removed broken string. Attached replacement string to spring and threaded through wheels (copying other side), then attached string to door. Tada! Done. Will never pay a call-out fee again (for this problem anyway...)

Pulled out dishwasher to access the sides. Removed onld lines and then unscrewed pulley from frame using socket / nutdriver. Replaced pulleys with new units supplied in the kit and then threaded new lines onto door and springs. Repair complete in less than 5 minutes.

You said the repair was easy and would take around 5 minutes to perform. You were spot on and the instructional video really helped do the job.

pulled it out, saw 'pulley' was fine, and put cord on spring and puled it enough to hook it on other end.end after running cord around the 2 pulleys, as it was on the other side. push it back and done.

We ordered a new lower spray arm. I was impressed that we could get one considering the age of our dishwasher. There is a gear under the rotating part of the spray arm that I turned counter clockwise. Then the old one lifted off easily.
I couldn’t find any good instructions for installing the new one. I tried reversing the process I had used to remove the old one. Finally, after I put it in place, I put my hand in the center of the spray arm and pushed down firmly. I felt it snap into place.

The video does a great job explaining the repair. I took the unit completely away from the wall and put it on its side, which I recommend. Only problem I had was getting the new part in the correct orientation to lock... try to pay attention to how the failed pump is facing when you remove it.

I ended up replacing the supply line as well as just moving it around caused a drip leak, guess it was about to fail. Pro tip: don't remove the old line until you have the new line in hand... but that's a story for another day.

Two philips head screws to get the arm reaching up to the oart removed. Snapped it in and I'm good to go! Clean dishes again! All for a 1/4" part.
Just followed the videi on this ste to make the repair.

I just followed the directions on the video that was part of the pictures for the door seal. I made sure that the channel was clean and the new seal pressed right in. i wish I had checked this site before I called a repairman, who wanted to charge me over $400 for a new one.

First we removed the two screws up under the countertop that secured the dishwasher in place. Next we pulled the d/w out from under the counter, having to unplug the power cord and feeding the drain hose into the d/w cavity from under the kitchen sink to allow this. On each side, attached to a metal spring was a nylon cord with plastic attachments that ran through two plastic pullies/wheels. The plastic piece on one of the nylon cords had broken...only on one side, so we were able to just look at the 'good' side to see how to attach and string the repair part through again. We pushed the d/w back in, made sure the drain hose under the kitchen sink wasn't kinked by pulling it back under the sink from the d/w cavity, plugged it in, replaced the two securing screws and were done. The old cord running through the pullies had always creaked when the door was opened, so while the d/w was out, we coated it w/ WD40. Piece-of-cake!

For easier access,removed both trays from dish washer. Pushed both clips apart from upper water arm, let arm hang, removed old spinner, replaced new spinner.

I first verified that there was 120 volt line voltage getting to the unit. I removed the outer door panel by removing the 10 torx screws located around the panel on the tub side of the door. Two of the screws are longer so note there location for reassembly. The door handle can now be removed. Pull the outer door panel away from the inner panel and remove the connector to the control board. Set the outer door aside. Remove the connector to the door latch.The latch is snapped in position at the top side. Pry using a screw driver to release. Snap new latch in position. Snap on connector, Reassemble door by first reconnecting the control panel connector. install plastic door handle. Mate door to inner panel. Note interlock tabs between outer door and inner panel near the bottom area. Install the 10 screws. The two longer screws are at the top holding the latch and handle.

Video was great help. Replacing the balance parts was easy. My wife and I are in our 80's. Mobility is difficult when it comes to working on the floor. Between the two of us we spent the majority of our time just getting up and down,