66513929K014 Kenmore Dishwasher - Instructions

Unscrewed mounting screw at top and bottom of duahwasher, pulled out dishwasher could see the pully on one side had broken. installed new part put dishwasher back in place and rescrewed mounting screws.

Followed directions here. Extremely easy repair.

Pretty easy for the parts. Taking the dishwasher out is the hard part. Typically, you should be able to unscrew the 2 screws holding the dishwasher to the underside of the countertop and then slide out the dishwasher to expose the cable assembly - but you also need to unplug the unit (unless it is hardwired), disconnect the hot water supply line from the angle stop (remember to turn off the angle stop) and sometimes disconnect the drain line from the vacuum breaker or garb disposal. You need to disconnect these things so that you can move the dishwasher out far enough to be able to see the entire right and left sides of the dishwasher. Once that hard part is done, you use a hex driver to remove the old cable pulleys, put on the new cable pulleys, and then feed the light weight cable through the pulleys - the end with the big plastic thingie attaches to the door and the other end attaches to the spring. Then you grab the spring and manhandle it onto the back end of the dishwasher chassis (look for the small hole in line with where the cable would line up. Careful as the spring attachment step could result in an injury - Hope this helps.

Started the rope onto the top holder, threaded the rope around the rollers and using the pilers pulled the spring forward to attach the other end of the rope.

just move the machine out and replace the string. this site is very reliable and and great company. since the dishmachine door cannot be closed, we first order door strike, ,,,, still doesn't work after installation. and return all parts and order the balance kit, now works fine after. we appreciate your help

First I turned off the water and power to the dishwasher.I removed the two screws on the front bottom cover plate, removed the plate. Removed the two nuts and bolts holding the dishwasher in place between the cabinets. Then I pulled the dishwasher out about 6 to 7 inches so I could see the spring, pulley and rope connections. Then I saw the rope on the right side of the door bottom had pulled through the connector. I ordered the part and next day delivery was great.(excellent service). The repair kit comes with both sides parts but I only needed one(for now). I reconnected spring to rope connector and threaded through pulley and to the door and job was done. A little difficult stretching spring so I put a long piece of wire to hold spring tight while connecting to rope but I worked out great. My husband said "great job, honey". I saved a $150 repairman bill....now I might go shopping (ha ha) Kim

Received the part. No instructions came with it. Luckily it was pretty simple to figure out. i removed the appliance from under the counter, saw how the part was attached on the other side and simply replaced the other side that was broken. Easy.

Disconnect top screws
Pull dishwasher out halfway
Notice how the other side is connected
Thread cord, use pliers to pull spring to connect.

The repair itself was relatively easy. I basically only had to remove the two screws that were securing the diswasher to the cabinetry, disconnected the water line and extended the diswasher out approximately 10 inches. I then replaced the part by hooking the new cable assembly to the spring and using pliers expanded the spring so I could snake the other end of the cable through the pulleys and attach it to the door. The otherside was my guide. This part should be modified to replace the two plastic ends with metal counterparts. This would allow the part to have a longer life especially in my case since the plastic end broke and not the cable itself.

Removed the bottom cover plates.
Removed the screws holding in the dishwasher.
Removed old single moving roller and replaced with newly designed double rollers.
Installed link(string).
Replaced other side rollers and link.
Reinstalled dishwaser.

Shut off elec. and water. remove bottom plate and 2 screws holding the unit to the counter top.
disconect elec wires to unit and remove water line.
Pull unit out from counter and replace cable to spring the same way as the unbroken side.
Slide unit back and reverse hookup.
My only problem was that the part they sent me was about a 1/2" shorter the the original and the door is hard to open.

I followed the Partselect video for the new installation. Very easy to follow which made new part installation extremely easy. Works perfect now!!!

Using Phillips screw driver, removed 2 screws at top of unit, slid it out from under counter. Removed and replaced both sides. The hardest part was to keep the blanket on the unit which I solved with duct tape. Slid the unit back in place and works fine. The repair man wanted $29 to come out and $150. To repair

Get a piece of stiff wire (medal close hanger) cut a Short piece and take a tool and roll a half circle on each end making the link length you need then attach the lanyard to the spring

repaired exactly as your video described......hardest part it getting unit out from under cabinet and back in.