633616 General Electric Dryer - Instructions

Checked the fuse box to see if any breakers tripped on the two 120 lines feeding the dryer.

Checked for clogged exhaust vents/hose/etc, cleaned.

Some paint flaking off inner drum around heat vent.

Unplug & disassembled unit. Took pictures for reference to help with reassembly later. Upon removing drum, found sagging heat coils, one broken, some heat damage to the housing near the top. Determined that more than just coils needed replacing.

Also checked each of the three heat sensors (cycling thermostat, high limit thermostat & safety thermostat) with the digital multimeter. All were positive continuity for low temps.

Tested ONLY the cycling thermostat on the kitchen stove with burner set to warm. Check burner temp with meat thermometer to see it exceed 120F. Continuity broke at high temp. Although the cycling thermostat seemed ok with my generic test, I decided to replace it anyway.

My understanding of the Safety Thermostat & High Limit Thermostat is that they work like safety fuses, breaking at dangerous temps, but not resetting afterward. So these were only tested at room temperature, not with heat.

With the unit open, I checked other components for signs of wearing out. Also cleaned the unit more thoroughly.

Reassembled in stages. The belt is the trickiest part to get back on the motor & tension pulley, it's just a little awkward to reach. Tested to make sure the drum moved freely and belt was correct before finishing the reassembly.

Checked to make sure the dryer was still level, after all the moving around, disassembly & reassembly.

Ran several supervised test loads. Felt the temperature. No tripped breakers or smoke. Exhaust was flowing unhindered. Clothes got dry.

I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!

I watched the repair video 3 times to make sure I was comfortable to do the repair.the video was very helpful.thank you ! Everything went well and the dryer runs great.

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

I replaced the drum bearing slides and also the main front drum bearing. First, disconnect the electric. Then I removed the two screws inside the door that attach the top cover, removed the top cover, removed two screws that attach the front cover, lift up the front cover and pivot it to the left leaving the wiring attached, removed the front bearing assembly by pulling it out at the top and then up, installed the new front bearing ring and snap it into place, installed the drum bearing slides, reinstalled the front cover, reinstalled the top cover, and tested the drum by turning it by hand first and then under power. The whole operation took less than 15 minutes....

Simply replaced it. I have ordered from Parts Select several times. Excellent customer service. They always have the parts that I need and ship them to me promptly. Great company!

remove the broken one and replace it with the new one

Opened panel, bent retainer tab, took off wires. Took out switch, put in new switch, replaced wires and knob and plugged it in. Off she goes. PS, how the hell did you get that part to me in less than 24 hours??? Thanks guys.

Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...

Took off old timer and put new knob on and it fit.

Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.

Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job

My wife was attempting to start a load of laundry when the start knob came off in her hand. I figured the inside of the knob had broken loose and the stem from the rotary start switch would be sticking out, well the stem had broken off flush and the knob was fine. After ordering a replacement, I jerry rigged the broken one with a large screw driven into it and put it back in place, worked great, just had to put a screwdriver into the screw and turn it to get the dryer to start. I felt it was fine to stay that way but the wife insisted we install the new one to put the knob back in place. The new switch arrived very quickly and went into without a problem, just four screws to remove the panel, two wire connections and was working again.

inserted the lint catcher into the opening to replace the old one

this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.