5KSM125BDP4 Whirlpool Mixer - Instructions

Followed web site's videos. One step left out of video.

Took each area apart. Replaced the gear and reassembled it.

watched how to repair

You tube has great instructions! I would suggest when you buy a part to let customer know that they need a food grade gear grease ordered to complete the reinstall of all gears and body parts!

I watched the university of YouTube videos, and followed their instructions.

Removed the rear cover to inspect the speed board. Replaced motor brushes and noticed the motor body nuts were loose and 1 was completely off. Cleaned up speed board and replaced the motor body nuts, tightened with nutdriver, adjusted speedboard governor screws and with new motor brushes worked like a charm. The very rough sounding motor noise was gone and the mixer has not operated so quietly ever.

Simply removed damaged gears. Very simple to do. Ordered gears. Replaced gears. Both working well ( so far. ) Machines are easy to dismantle. Just be sure to put the screws back in the holes you took them out of when dismantling...no lost screws. On the smaller model, took pictures of the wire positions to be sure they were replaced in the proper order. Larger model had no wires to remove.

I am not handy, but was able to follow this YouTube video and do this repair easily and successfully: https://www.youtube.com/watch?v=1QsgPIL9FpA

I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!

Found control backplate out of adjustment. Should be nominal 3/8".Broken speed control spring which attaches to backplate bottom.
I recommend Loctite Blue to complement locknut's when adjusting RPM of "Stir" speed

I watched a short video on replacing the worm gear, although I did not know what the problem was until I watched the video. after the video ended I took the mixer apart and found the problem located a parts number an placed my order. got the part in one week put in the new part in about 20 minutes and it work like new. and the price was very reasonable

Repair went well after I figured out how to dis-assemble the mixer. Used straight & phillips screwdrivers and a small hammer & punch to drive out 3 pins. Ordered part# PS734233 pinion & shaft as shown in the parts page, it arrived on schedule, received part # 240210-2. Only problem was the new pinion had 10 teeth, the old/failed pinion had 11 teeth. Could not learn from anyone I called at PartsSelect or Whirlpool if the 10 tooth pinion was the correct part to use.
The teeth appeared to mesh with the mating gear,
installed the new pinion, reassembled and it worked fine. Not sure if it made a noticable difference in the output shaft speed.

Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!

I watched a YouTube video all the way through, then watched each segment and followed along with the video. It was messier than the professional repair guy, but it worked out fine. This is not a difficult repair when you can watch a video and follow along. It saved me about $130.

Watched a couple of youtube videos and it was easy.

With a screw driver remove the screws holding the old base in place. With a flat head screw driver carefully pry and remove old mixer base. With 600 grit sandpaper clean and make smooth any burrs or rough spots in the mixer base recessed area. You can use some light grease and coat the outer edges of new mixer base and place in the now cleaned mixer base recessed area. The new base maybe a tight fit and not be fully seated in the recess. If a tight fit, place the piece of 2x4 piece of wood over the new part that is in the recess and carefully tap the base home using the sledge hammer. Check to see, if the base is fully seated. If not fully seated, tap again When fully seated replace the screws. You may have to adjust the height of the stand mixer head with mixer paddle attached for proper clearance between bowl and paddle. See your mixer manual for adjustment procedure