41748102700 Kenmore Washer - Instructions

Remove top of washer, remove door lock assembly,install new assembly replace top.

replaced the two shocks with the new ones by removing the pins that held the old ones in place.

Removed old shock abs. (both sides). The one side, I had to remove the speed control board to access the lower nut on the one shock. Install was fairly easy however, it did not fix the washer. Apparently there was something else (either a switch, the control board or the motor) needs replaced too.

My shocks on the washer were broken, in part because of age, the other is broken spider drum inside the barrel. Was very easy to do the shocks. Unhook water connections and power. Move washer away from the wall. Remove the back cover from the washer. On the left side, you have to remove two screws from the electronics control box so you can gently move it out of the way. Then grab the plastic pin with some pliers and pull while depressing the locking lug on the end of the pin (Very important to depress the lock or you will have to buy new pins) Remove both pins for each shock. I used some high pressure grease on the pins when I put it all back together. Was a quick fix. Unfortunately had to take it all back apart as this was only a small part of my issue with having the stainless drum being broken inside.

I just pushed the washer on its side on a price of wood. I put a pan to catch the drain water.It was then as easy as detaching two boots and two bolts that hold the drain motor on.Do it in reverse and you got it.Oh first don't forget to unplug the electrical wires ect.

love parts select have used them several times for parts great company

As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

Removed front panel, used socket to compress lock tab on plastic pins holding shocks. Still taks a little effort to get them out. The one behind a plastic drain canister is a proble as there doesn't seem to be a good method for moving that canister. I think that's why the spare pin is provided.

Sadly, my case was one of the lower percentage where the problem is in the rear bearing area. The shocks were, the top support springs were good but the rear of the washer drum was shot. Opted to replace with new washer rather than go through the much longer repair with the almost $300 in parts.

Remove screws take off striker .Put striker back on with screws back on

Tighten screws. Took 5 minutes

Very basic replacement- 2 screws in and out. The part did not come with screws to be sure to save them if you remove the broken part ahead of time to make the process smoother.

Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done

just unscrewed the old one and put a new one on.
I bought two just in case this one breaks too.

The instructions that came with the new shock absorbers were very detailed and walked me through the repair step by step. The new shock absorbers are much better quality than the old tube style shocks.

easy repair. I went to the back of the washer and removed the two(?) screws that held the top panel on. Then moved to the front of the washer and unscrewed the two screws in the door frame holding the lock assembly. Pulled it up and out from the top of the washer and disconnected the three wire connections. Then I just reversed the process with the new part. It all worked great. This website rocks...
Phil
Jax, FL

Removed the 4 screws holding the top on. Pulled top forward to release front catches and stood top up out of way. Removed 2 screws holding door lock. Could not unplug wire plugs from door lock because wires too tight. Removed 2 screws holding lower front panel and removed panel. Pulled door lock down and unplugged old lock and plugged in new lock. It was easier to position door lock to reinstall screws by working from top, so top removal wasn't a total waste of time. Reinstalled front panel and top. Machine works.