41510129 General Electric Dishwasher - Instructions

Removed rack slide end caps. They broke off because of brittleness. Removed rack, then used pliers and/or flat blade screwdriver to remove 4 rollers and axle assemblies. Replaced with new rollers/axles. Return upper rack into slides and installed new end caps. New caps slightly different than old but easily clip into place Upper rack works lile new!

My GE Potscrubber 940 would not drain on all cycles. After checking the basin traps and not finding any blockage in the water drain line, I suspected that the problem was with the drain solenoid, since the motor was running smooth. I removed the dishwasher, primarily by removing the water supply line on the left side from the water inlet valve and disconnecting the electrical connections. Make sure you turn off the water and electricity before you do any work on the dishwasher. With the dishwasher taken out and on its side, the drain solenoid unit will be visible near the motor in the middle assuming that the front bottom panel of the dishwasher has been removed. I found mine to be all crudded up. I removed the electrical connections and the solenoid bracket. Then by using my multimeter, I found a bad resistance reading (infinity) for the solenoid. I ordered the Drain Solenoid Repair Kit and replaced all the items except the plastic rocker arm. Naturally, just reverse your steps to get the dishwasher back together. Turn the water and electricity back on and fire her up. Check for proper operation and any leaks and you should be done.

Pulled the lower left side end of the old door gasket out of door gasket retaining slot and slowly and evenly continued to work my way around the door pulling the door gasket out of the retaining slot until I reached the end. I installed the new gasket into retaining the retaining slot beginning on lower left side and then slowly and evenly working my way around the door inserting the new gasket into the retaining slot. I was careful to make sure the two cutout portions of the new gasket's retaining edge were correctly positioned in the lower corners of the door.

As suggested. Pull washer, remove screws from top and replace with new part. Very simple and easy if you follow steps furnished by this site.

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

Shut off water, disconnect power,remove
Faulty valve,install replacement part.

We ordered the pump kit by model number and it was a perfect match.(It was on our door step in 2 days with normal shipping!) Three bolts and a couple of electrical connections later and the pump was off The install was just as easy. The instructions were very easy to follow.It's great to find a company these days that knows what it is doing and does exactly what it says it will do.
Kudos and thanks!

Removed old basket, put new one in. New basket fits but it is larger then the old one so it takes up more room leaving less room for dishes. My dishwasher is apartment size.

Service from PartsSelect was very prompt.

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

Very simple repair: assemble the wheel/clip assembly. Attach to lower dish rack.

I was very happy with the fast delivery by PartSelect.

took off the end clip, pulled the old wheel off and unclipped the bracket from the rack, then clipped the new assembly on...Simple!

I have to be honest. At first I called a repair person, but it was Sunday so he couldn't come till the following week. Then my incredibly intelligent, industrious, and internet-savvy wife found your website. We saw that others had had the same problem. The part we needed was right there.... voila! 2 days later I had the part in hand. Not being the most handy of handymen, I followed the directions that others who had the same problem had posted. Yep, it was that simple -- And a heck of a lot cheaper than a repair person. Your website was very valuable, and I definitely will refer it to others looking for a part for a home repair job.

Super-easy and quick repair -- quality part snapped right into place.

First, remove the two access panels to the bottom of the dishwasher, each had two screws. Then, disconnect each old door cable and eyelet assembly, and the two springs. Now, connect the two new cable assemblies, and reconnect the two springs, one at a time, between the eyelets of the cable assemblies. Finally, replace the access panels