3XART718F00 Whirlpool Refrigerator - Instructions

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

Simple replacement, snapping the plastic rail in place and putting the crisper drawers back in. We were very happy that you had the part, your site made it easy to find, and it was shipped to us promptly, and at reasonable cost. Thank you.

pulled the fridge out and took the old ones out and put new ones in .... glad to find the right drawers though.... they fit perfectly....

Took out the old drawer and put in the new one.

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

Repair was very easy. We removed the glass from the shelf above the crisper drawers and then just snapped the rail into the frame.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

The instuctions say take the door off. I didnt find that necessary. Made sure the new gasket would fit. Pulled the old gasket out inline with the door instead of away. The gasket came off like an innertube on a bicycle. Installation of my new gasket was easy. I started on a corner hooking the lip behind the ledge and worked my way around the door. 10 min maybe. That's it

Removed glass shelf. Removed both crisper bowls. Removed broken rail and put new rail in! Hardest part was taking out all the items sitting on the glass shelf. Actual installation time under 1 minute.

poured boiling hot water into drain; removed most ice with hair dryer. Clips(2) positions the defrost tray & drain under the freezer condenser. A "home-made" coil of 18g copper wire inserted into the drain hole, & secured to the defrost heater further prevents the drain from iceing shut!

Looked up the refrigerator model number, found parts break down and ordered wheel assy...thought it was the wrong but wheel size was right...read the instructions (good thing) and found out you had to slide entire bottom panel out 1/2 inch to access a hidden pin...did as the instructions said, slid out the bottom panel, found pin as advertised, removed pin, broken part fell out, replaced the wheel assembly, repinned, slid the bottom panel in (a bit more harder than getting it out), replaced all screws and was completed in about 40 -50 minutes. Good thing it came with instructions!!

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.