25357109607 Kenmore Refrigerator - Instructions

I followed step by step instruction in the hinge kit; Replacing the old hinge with a new hinge and two new plastic cams in the kit. The kit hinge has an adjustment to level the right door with the left door. Everything is done in 20 minutes for a senior guy like me. Very easy.

unplugged the refrigerator after pulling it away from the wall. Removed the water tray fairly easily. I read from other experiences about the water tube, i was prepared. I clamp a surgical clamp to the tube before removing the dispenser module. Look at the water dispenser you will see a white tube protruding, clamp it to prevent it from backing out. I removed three screws and the ice/water dispenser removal was a cinch. Two screws were removed and the actuator snapped out and new one installed. Be careful of the panel power strip, if it comes out it can be easily reinserted. Just make sure you get it in correctly. The fitting holding the strip will slide down slightly , enough to insert the power strip and push it back in. 30-45 mins only snag was not paying attention to the orientation of the power strip. If I had removed it at first would have made the job simplier. in other words i installed the strip backwards and when powering up had no display, removed panel reversed the strip and all is well.
Even with this mishap, 30-45 min was consumed. Have fun DIYER's

removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

very easy to install...shipping was really fast...i would order to this website again....

Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.

The replacement glass was a perfect match !!! So pleased...
I was very surprised on how quickly I received my part. I
would definitely recommend your Company to my family and friends. Thank you

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

The old support just unscrewed & then the new one screwed right on with two screws.

Removed the Plastic Cover at the top of the door. (One Phillips Screw ) Removed the Hex Screws with socket set. Lifted EMPTIED door off bottom hinge. Pulled the broken bearing out with needle nose pliers. (Very Easy!!!) Placed new bearing into slot and reversed the procedure. 15 minutes tops. I spent more time cleaning the door and gaskets than replacing the parts. Funny thing, I called the local appliance parts store and they stated this is a common problem. However, for such a common problem, they didn't carry the part and it would have cost more than what I paid here. Additionally, I paid for 3-5 day delivery. Part was here in 2 days. Awesome!!!! I'll always come here first for all my parts needs. A+++

loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done

Pull refrigerator from wall and disconnect the water line and unplug the power.

On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.

Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..

Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.

Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.

In about an hour you should have ice filling the bin. Enjoy!

Turn of power at the circuit breaker.
Remove the water tray by pulling straight towards you.
Remove the three screws at the bottom of the control panel.
Have someone hold the control panel while you remove the six small screws that retain the circuit board.
Gently ease the circuit panel away from the plastic frame and disconnect the six wire connector on the left hand end, followed by the two light connectors with black & red wires, then remove the four wires with spade connectors from the microswitches - noting where each goes. The control panel & circuit board can then be set aside.
Remove the three screws that retain the interior plastic frame. The plastic frame can then be eased forward taking care not to pull out the water pipe. This allows access to the screws that hold the actuators, which should both be removed. Unhook the spring & remove the broken actuator. Feed the new actuator wire up from the bottom of the frame and insert the left hand pivot first and twist gently to snap the right hand pivot into its recess. Replace the retaining plates & screws. Don't forget to the hook the actuator spring into its clip. Test the operation and ease the plastic frame back into position and attach with the screws.
Re-connect and reassemble the circuit board and front panel in the reverse order.
Power on and enjoy a glass of fresh cold water! You may need to press the reset button on the front panel to reset the lights in the actuators.

It wasn't clear how to disassemble the Ice / Water dispensing unit to get at the lever for replacement BUT the website had a great exploded parts view of the door and assembly so I was able to print that and from the diagrams you can easily work out how to pull it apart..
A bit fiddly and you need to power down the Fridge as there's 120v behind this panel (tip : dont drag out a heavy fridge, flip the breaker at the main panel to isolate the power) .

All fixed for $50 , compared to having to call out some guy who'd charge me $100 plus parts !! great deal !
Thanks !

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.