Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 20236 > Instructions

20236 Jenn-Air Wall Oven - Instructions

All installation instructions for 20236 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 20236
181-195 of 250
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

lower heating element and lite burned out.

  • Customer: william from gaithersburg, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 21 of 610 people found this instruction helpful
This is what people need to know. Unit burned out 7:00pm Thursday, ordered the parts 11:00am Friday, FedEx delivered it to me Saturday at 1:00pm. How can anybody ask for more. Good price and easy to install. Julia W

Old grate were nasty

  • Customer: Greg from Ortonville, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I actually bought these for a friend. He cooks for everyone that shows up. I haven't seen the new grates in action yet. Will have to show up with some meat and test them out.

The burner didn't heat to full temperature.

  • Customer: Stephen from Grants Pass, OR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First turn off the power to the stove/oven. Next I removed the 4 screws located on the bottom surface of the control panel. You need to open the oven door to see/access them. The control panel can then be removed by rotating the bottom outward which allows the flange on the top to disengage. Next remove the two screws that hold the switch to the control panel. Note which wire goes to which spade connector. A quick photo can help. Undo the wires. Remove the old switch. Reinstall the wires. Mount the new switch to the control panel. Mount the control panel back into the stove/oven. Turn on the power and test. The burner now works as new!

glass in oven door was broken

  • Customer: Vonnie from Indian Rocks Beach, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We took the door off, you have to be careful of the hinges popping back. We put small screwdrivers on each side and held the hinges out, this made the door easy to just stand up and slide back on the hinges. The glass replacement was simple just a few screws. We spent $127.00 on the part and shipping and a new wall oven would have cost us $1500.00. Thanks for making this part available.

It took high torque to dislodge the screws

  • Customer: Jacob from Kings Mountain, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the two screws and inserted the new element. Applied a light coat of petroleum jelly to the screw threads and reinstalled.

Light bulb failure

  • Customer: Grant from Alexandria, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Replaced worn seal

  • Customer: Horace from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the door. Place small screwdriver in each door arm to prevent extraction. Remove approx 20 screws. Remove the seal. Replace the new seal. you will need help in holding the seal in place until you car install at least two screws. Very straight forward. Took 20 minutes. Even a cave man can do it.

Burner stays hot

  • Customer: Gregory from snellville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.

very old grease filter.

  • Customer: Eliane from Potomac Falls, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy to replace the filter, nothing to it, take out the old filter and put in the new filter.

Simply replace the grease filter

  • Customer: MaryAnn from Scituate, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Thanks for carrying this part for my old stove. And thanks for the great service.

Burned out lower electric oven element.

  • Customer: Bruce from Woodstock, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I simply removed all the oven racks so I could reach in, removed two screws, un-clipped the old element and clipped in the new one. Put the screws back in and popped in a chicken ready to bake. Delicious.

Door seal was worn out/burned /leaking heat

  • Customer: Christopher from Toledo, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Took the oven door off hinge. Took door apart pulled off old seal from inside of the inside panel of door. Replaced with new seal.

Burner would stay on high, on all settings.

  • Customer: Robert from Attleboro, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.

Thank you for your help!!

Bob

Burner always on high, no temp. adjustment.

  • Customer: Woody from New Castle, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!

burner cartridge terminal broke due to electrical shock. circuit shortage caused the problem.

  • Customer: Ge from Solon, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.
All Instructions for the 20236
181-195 of 250