1902 - Instructions

Followed PartsSelect instructions, the Compactor was appoximately $1000. when I purchased it. The kit was $26.14. I will forever be a customer of this company. Thank you, Brian

Laid appliance on side - removed top sheet metal cover and bottom sheet metal cover. Broken delrin ring gear was on bottom of bottom cover (housing). Gear had broken off of its hub, which also was the sprocket chain drive for both acme screws driving the compactor platten. Motor had to be loosened so that the chain could be removed from the old sprocket hub, and the new delrin ring gear - with new sprocket hub attached - could be mounted on its fixed spindle. With new delrin gear/chain sprocket mounted, the motor had to be spaced and tightened to allow 0.010 inch lash between the gears. The only instructions included with the new gear was how to do this - by placing a piece of paper in between the pinion gear on the motor, and the new ring gear, and then tightening the motor into place. This was done, the sheet metal covers were re-installed, and the compactor works just fine. There is a design flaw in the original (KitchenAid) engineering of the gear, however, and I expect that in the next four years this will probably happen again.

Thanks to Parts Select and their detailed instructions it turn out great! Replacement Parts fit Great!

Took out old gears replaced with new very easy with your dirictions.

replaced the large gear and put it back together.

Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.

Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.

The part was suppose to come with instructions, but did not. However, it was easy after reading the comments on-line, and discovering that the front cover had to be removed in order to expose the whole switch and wires. I did drop one of the mounting screws down the front of the compactor and was not able to recover it. So, I had to make a trip to the hardware store for a replacement. They couldn't match the remaining screw but I found 2 similar ones with lock washers and nuts that worked just fine. I saved a $90 service charge and probably double the cost of the switch by doing it myself.

changed out the big gear that was broken

Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.

The part that doews the actual compacting would not move correctly. The machine would not stop because the part never contacted the spring loaded switch. I had known about this for about a year, but put it off until it stopped working altogether. I ordered 2 power nuts and rec'd them in B.F.E. Alaska in about 5 days. I quickly replaced the parts and the machine works like brand new again. I estimate this compactor to be at least 10 -15 years old and replacing the occassional part once in awhile is a lot cheaper than buying a new compactor.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

I removed 3 screws from the back and 2 smaller screws from the sides. I removed the broken handle, installed the new handle and inserted the 3 screws. The 3 screw hole aligned perfectly. The replacement part did not have predrilled holes for the 2 side screws so I drilled the holes and inserted the 2 smaller screws. Job done in short time.

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

very easy to fix. all it took was pulling the compactor out to unplug,take off the removable front nob, unscrew two screws located just below the front panel.using needle nose pliers to remove the actual switch, unplug the wires conected to the switch and put the new one on the same way. It almost took me longer to write this discription than it took to fix!