110773882 Kenmore Dishwasher - Instructions

I used the screwdriver to pry the old lid off of the horizontal pin upon which it rotates. One must be careful before removing the old lid to note how the return spring is deployed. The short legs on the spring must be in the lip of the lid before you snap the new lid onto the horizontal pin. It was helpful to lubricate the two catches on the lid that snap on the pin with some liquid soap before attempting to snap them on the pin. After the lid is snapped into place and the short legs of the coil spring are in the lip of the lid, use needle nose pliers to attach the other end of the coil spring to the pillar where it was before you removed the old lid. There are videos showing how to do this on Youtube. The spring part is a little tricky. The video makes it look a bit easier than it is..

Mine is a Ultra Wash 111
I followed the repair video on your site but my dishwasher was a little different. Not enough that anyone could still understand the video and not get it disassembled. The video shows two ball checks but mine doesn't use them where the videos shows. I put them in anyway because I called Whirlpool, who made my washer, and they assured me that they should be in there. They got sucked through the dump impeller and plugged the discharge tube so I had to disassemble it again and take the ball checks out. Lucky for me nothing got damaged. I then got a hold of someone on your chat line that got me to the correct parts view that shows where the ball check is suppose to go on my washer. During working on my washer I realized the squealing was because the bottom bearing on the motor needed oil. So all and all I'm happy because it runs quiet and it works fine. Thanks Greg

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

Great fit. take out old one and drop in new one. Piece of Cake.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.

As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.

I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.

The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.

I watched the video link sent in an email and followed exactly what they did in the video. I removed the star head screws holding the door liner in place. Then removed the protective cover on the inside. I disengaged the component holding the latch in place. I replace the component that holds the latch in place and then snapped the new latch in place. I turned the dishwasher dial until the prongs were fully retracted. I replace the protective cover and then put the door cover back in place. I initially only placed the left bottom star head screw until I was sure that the latch was going to release. I tested that it was working properly by slowly turning the dial on the dishwasher control. Once I knew it was working I replaced the rest of the screws.

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

Unscrew the top bracket on basket of upper spray arm assembly. Remove entire upper spray arm assembly. Remove old spray arm. Install new spray arm and new supply tube being careful to align the upper bracket with slot on new spray arm and supply tube.

Got the new door and tried to put it on. The door went on very easily. However, there's a spring that opens the door when the main wash cycle comes around. I never did get that spring right. None of the drawings showed the correct position and after an hour of trying to get it to work right, I gave up. The door comes open slightly (but not because of the spring) when it's time, and the liquid soap runs out due to gravity. But I wouldn't try to use soap powder because the door doesn't come open far enough.

repair was very easy did need to go to the hardware store for and adapter for the hose to water inlet valve as mine had a smaller diameter connector. Otherwise followed both videos. Needed a shopvac to remove water in the bottom of the dishwasher

No Water supply to Dishwasher. Turned off main Supply valve under sink.First took off old Diswasher supply valve and repaired it by cleaning it and it worked for two weeks. I ordered the part, but then cancelled it and Partselect service was great and cancelled it immediately. After it went down after 2 weeks I re-ordered it and it came in 4 days.
To Take this part off I removed mounting scews with nut driver, disconeected electronic plug connector, removed the compression fitting from the water supply and removed the outlet hose..reversed all of the above to install.

The repair went well with the major problem being I replaced the drain hose without removing the dishwasher from it's position. Due to this I removed the drain end with out being able to see the hose and put it back on by feel. Over all I was back up and running with in 30 minutes and everything has worked very well so far.