1107109910 Kenmore Washer Dryer Combo - Instructions

Stopped by a friend who is an appliance repair person. He walked me through the Roper repair.
Removed the two screws, pulled the control panel up and back, disconnected the two wires. Sprung the two clips with a large screwdriver. That gave me the room I needed to do the repair. The hardest part was lining up the cover to go back on level. Part worked perfect, everyone was happy.

Shut off both water valves and used a cup to catch water from hoses. Removed top control panel that's held on with 2 phillips screws. Remove top screws on the back to gain access. Was able to access the valve by pulling slightly out on the top corner.

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...

Removed two screws holding top control section on, and folded back the control panel. Removed two clips holding cabinet on, tipped cabinet toward me and off. Removed and replaced water valve, being careful to mark hot/cold hoses, and secure the internal hose to the valve with the spring clamp. Most difficult part was lining back up the cabinet when putting it back on the base, but a few minutes to line up tabs and get the front of the cabinet UNDER the front groove in the base got it secure. Works fine now.

Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.

1. Unplug washer, close hot and cold water supplies and remove water hoses from washer inlet valve.
2. Remove two screws at the bottom of the front of the control panel.
3 Remove two screws at the top of the back side of the control panel.
4. Remove control panel.
5. Remove two retainer clips that hold the back panel to the top of the cabinet by prying them out from the front with a large screwdriver. (Probably the most difficult part of the job.)
6. Use a socket or nut driver to remove the two screws that hold the valve to the back panel.
7. Lift the cabinet from the bottom rear and tilt the cabinet forward until you can access the valve.
8. Remove the wire harnesses from the hot and cold valves taking note of the wire orientation. (The red one will go back on the hot valve.)
9. Use pliers to open the hose retainer clip and slid the clip out of the way and remove the hose from the valve.
10. Reverse the process and you are done!

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

The replacement of the water inlet valve was not too difficult after reading the steps posted by others. The main step is to unscrew the top control panel first, remove the top 2 screws of the back panel, and you have easy access to the water inlet valve. No need to remove the entire back panel. Follow the instructions which accompany the replacement water inlet valve and you should have no problems. The washing machine now fills faster with the replaced water inlet valve. The replacement inlet valve arrived within 2 days of ordering! Thanks for the superfast shipment!

Initially, we thought the problem was in the water inlet valve and we changed it out. It went OK although the Kenmore almost fell apart after the removal of a few screws and the control unit.
Only thing was that it was unncessary. The real problem was not in the cold water turn on valve, but in the hose. The hose was special in that it was designed to shut off under emergency conditions. It appeared to be able to passs water when tested at my sink, but when connected to the washing machine and under presssure, it would not pass water. I had installed the part by this time so I left it there. I found the Kenmore washing machine rather flimsy in it's construction and tended to totally come apart once a few screws were removed.

This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.