1107109910 Kenmore Washer Dryer Combo - Instructions

Checked fuse with Volmeter, had continuity (acted as a short) not the problem. Disconnected Hot Surface Igniter 2 Position connector to check resistance for a range of 50-300 Ohms of resistance with Voltohm Meter. Meter read open (High Resistance). Removed Igniter by unscrewing 5/16" hex nut on igniter plate assembly and noticed silicon carbide element was cracked in the middle. Ordered a new igniter and noticed assembly was required. Be careful here as igniter element is fragile, also do not touch it with your bare hands. You have to lay down on floor to reinstall igniter assembly and you might want to practice anchoring the defective igniter to gain confidence. Finally with slow movements anchored new igniter assembly and turned on dryer. Watched igniter glow heating gas valve and heating gas flame returned. Dryer fixed for a few hours of study online and cost only $24, plus learned how the gas dryer works.

Removed the old hoses and screwed on the new hoses.

I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke

Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place located just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.

The hardest part was removing the machine's cabinet. 2 screws on either end of the control panel, tip the control panel back out of the way and remove 2 clips, then slide the cabinet off the front. Replacing the valve was very easy. I didn't need the mounting plate that came with it. At first it looked like the screw hole wasn't going to line up with the hole in the back of the machine, but then I noticed that the valve had a groove that allowed it to slide downward on to the back. Pretty easy overall.

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

all that was required was to push the catch into the slot notools needed.

You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

Unplugged it. Removed the two screws holding the panel on. This model had the screws on the front. Unplugged the wire harness and tipped the control panel back. I popped off the clips for the cabinet and slid it off the frame. On the back of the washing machine, I unscrewed two screws that held the water inlet valve in place. I unhooked the two wire harnesses on the inlet valve. Slid the clamp on the small hose back and pulled the hose off the inlet valve. Once I had the old part off, it was just a matter of doing it all in reverse. I did have to screw the metal plate that came with the part onto the part before I installed it. I put the small hose onto the new inlet valve and slid the clamp back in place on the hose. Put the new valve through the holes on the back of the machine, and replaced the two screws. Click the two wire harnesses back on, making sure to put the RED harness on the HOT valve (the holes have the stamp H and C on the back of the machine itself. Slid the cabinet back into place. Put the wire harness back on. Replaced the cabinet retainer clips. Slid the control panel back into the slots and replaced the two screws for it. That was it. All told it took me 15 minutes total. This was an extremely easy repair.

Followed the instructions. Removed two screws on front panel, flipped it up and popped up the retainer clips. Tipped the washer body forward. Unscrewed the old valve and replaced with the new. Reversed the previous procedures and put the whole thing back together. I had put up with this low flowing water for a couple years. Now it fills like new!

First I unscrewed two screws holding the back panel. Unscrewed the screws holding the water valve onto the back panel. With a screwdriver, pried the panel out far enough to pull the old water inlet valve out. Remove the connections on the old valve and replace with the new one. Screw everything back together. Fairly easy repair. Cold water flows like new and the noise is gone. Hope to get another few years out of the washer for this $25 fix.

Simple repair. Unplugged power cord, turned off water spigots. Removed the two screws under the control panel and rotated it up and back out of the way. Popped the two retaining clips (that's much easier now that I know to simply stick a large screwdriver straight down vertically into the front portion of the clip and lean the screwdriver back, rather than try to pry the clip out by levering under it against the washer top) holding the main body panel to the front of the washer and tilted it forward but not all the way off.

That allowed plenty of room to get at the back panel where the valve assembly is. There is some sort of plastic tray over the top of the valves that's kinda in the way so I popped it out by squeezing its plastic retaining barb with needle nose pliers and forcing it back thru the metal panel. Two screws hold the valve assembly on, and of course the water supply hoses are on one side and the fill hoses on the other. Removed and placed them on the new valve in order

The replacement part comes with a mounting plate and is not an exact duplicate. I screwed the assembly to the plate, but the holes in the plate don't line up perfectly enough to allow a second screw to be used. I could have drilled in a new one if I was willing to move the washer even farther out but a single screw holds it plenty well enough for me. Be sure to attach the correct electrical connectors and water lines to the new valves.

Reassemble in reverse order BUT TAKE CARE NOT TO PINCH THE CLEAR PLASTIC TUBE that runs from the water level switch down behind the control panel when you rotate the control panel back into position. I watched my washer fill almost to overflowing before realizing something was wrong. After 2-3 unsuccessful examinations I finally realized the tube was caught between two panels of metal and the controls were not recieving the "I'm full" signal from the wash tub. That would have been a mess if I hadn't watched a wash cycle to double-check my work.

My washer sounds brand new and fills faster. $30 shipped and an hour of work.