1106518710 Kenmore Dryer - Instructions

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

This was a classic easy repair and I am sure saved us bundles on a service call.

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

I googled the problem, then came across a site where somebody had experienced the same problem, and they changed the door catches to resolve it. I did a search for Whirlpool parts and found "partselect.com". I followed the instructions on the website and located the parts very easily and also discovered that there was a video on how to make this repair. We were tolerating this problem for quite some time and now the problem is resolved, thank you...

I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!

Repair was simple, minus pulling the drive motor shaft out of the back fan. The female end of the dryer fan was made of plastic, so the socket wrench cracked the plastic end. Other than that, the repair was simple and easy to do. Much better paying the $88 for a new motor vice paying $400 or more for a new dryer. Dryer has run like a champ since replacing.

Screwed in light bulb and glass protector

very easy

The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!

In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!

First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in about 10 minutes.

The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.

Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!

removed the broken part and replaced with the new one

take the old latch out and pop the new one in. Your repair kit worked perfect.