11028012012 Kenmore Washer - Instructions

Found common diagnosis and instructions on internet. It is not difficult to replace.
Unfortunately, this new latch assembly did not fix the problem.

Took off washer body 6 screws
Took off old sensor installed new
Very simple and smooth

Turn off the water. Disconnect both hoses. Remove the plug from the outlet. Remove five screws with a nut driver from the back panel. Remove the back panel. Remove two screws from the cold water valve. Pulled out the old valve. Install new valve with the two screws. Reinstall back panel with the five screws. Reset codes to the washer. Tested out washer. Works fine.

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

Watch video on the site and the insulation will be easy and take about 30 min.

Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!

the repair went well but I still haven't received a refund for the order was was sent incorrectly. Order #22085769 order date 2/3/23

My daughter is the handy one in the family. She followed Steve's video installation steps and in an hour i was washing clothes.

There are a number of videos showing how to do this repair:
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut driver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.

I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.

I laid the washer on its front side to access underneath. I removed the original washer pulley system and actuator very easily to replace them with the new parts. The new/updated model actuator for my machine was a little bit challenging to maneuver around existing parts to make work, but I eventually got it installed. The plug was angled very differently than the original plug on the actuator, but it was a tight fit. There was no issue installing the washer pulley system. Hooked washer back up to power, water lines, drain line, and the washer has been working perfectly since.

Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.

Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.

Took off back, popped off top, replace valve

Followed instructions.

Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!