11021292011 Kenmore Washer - Instructions

FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.

I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.

The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.

Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!

I watched your video, followed the instructions, and
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and within 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.

I basically followed the video that was available on Partselect.
I had trouble getting the top of the agitator separated from the lower but I used a length of 2x4 and gently tapped this with a hammer (so I wasn't hitting the plastic directly with the hammer, never a good idea). I few taps around the perimeter of the upper agitator and it came apart. The rest was quite easy. I replaced the seal since it looked pretty worn when I first removed the inner cap.

Followed youtube video. Great instruction.

That OK , easy.

Followed instructions on website video.

Gently pry top of agitator off with small flat-blade screwdriver. Using the square end of a 1/2-inch socket extension, unscrew the plastic center "nut." Lift agitator off, remove center cone that holds the dogs, slip the retainer ring off, remove the worn dogs and replace. (Great opportunity clean the soap scum off the agitator!) Reverse the process to complete the repair.

Removed the agitator assembly with a socket wrench and extension, replaced cogs, reinstalled assembly...took about 10 minutes because I dropped the assembly once, and had to reassemble it. An absolute "piece of cake."

Removed top portion of agitator to expose the nut which held it to the shaft and removed the nut with a socket and ratchet. Removed the entire agitator and carefully took apart the plastic part which held the old directional agitator cogs (4 of them) and removed them and replaced with the new ones which I had ordered. I then reassembled the agitator and dropped it in place and fastened & tightened the one nut which I had removed earlier. The entire process probably took about 10 minutes and we immediately tried the washing machine and observed that the top portion of the agitator was turning exactly as it was supposed to and I am extremely pleased that I was able to make the repairs myself. This was a very pleasant process and I would highly recommend your business to my friends and relatives. Thank you very much for your efficient help.

Sincerely,

Ken Lancaster

I removed the center cap from the agitator, which then exposed an inner cap with rubber seal. These were both easily removed with no tools... just a slight pull. Then the center screw was exposed. I removed that "one" screw and pulled the upper agitator assembly off. The old dog ears literally fell right out. I simply ensured that I placed the new dog ears in the same direction as the old, which is not hard to remember because the little housing piece that holds them is molded in the angle of the ears. Putting it back in took the most time because the new ears can easily fall out. In order to overcome this I had to assemble the pieces that had been removed and carefully put them back in place. At that point I had to manage to get the screw back into position and tighten it up. I put the inner cap with seal back in place and then the agitator cap... Done! It's an old machine but works great with a simple repair. The dog ears were so inexpensive that I purchased two sets. Great site!

First I popped off the very top cap of the agitator. I then used a socket extension to access the mounting bolt in the interior of the agitator. Once the bolt was loose i pulled the agitator off and dropped out the middle piece. With this out i switched the 4 cogs with the old. I then held the agitator assembly upside down and placed the middle piece back in. The most difficult part was aligning the agitator back onto the bottom part. Screw it back in place and pop the top back on.

The repair was very easy, I took the top cap off the agitator and removed the recess bolt and pulled the agitator out of the washing machine,put the agitator on the floor and put my feet on the sides of the agitator and pulled the top haft apart,replaced the agitator directional cogs put back together work great