1066686000 Kenmore Refrigerator - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in less than 24 hours from my order placement.

Just like the others. Unplug the refrigerator. Loosen the top two screw and remove the bottom screw. Unplug the unit, plug in the new one, slid the unit over the top two screws, replace the bottom screw and tighten the top two screws. Done. I ordered the unit Sunday it was shipped Monday and arrived Phoenix Wednesday, shipper then rerouted it to Tucson Thursday who sent it back to Phoenix on Friday and finallydelivered it Saturday.

First I removed the ice bin to give me room to work. Then I took out the screws that held the old ice maker in place. I disconnected the wiring. I then plugged the wires of the new ice maker into the old wiring harness. I put in the bottom screws and loosely connected the top screws. I checked the level of the ice maker with a small level and then tightened the screws. The nest thing was to install wire level that shuts off the ice maker when the bin is full. Finally put the ice bin back in place.

Super easy! I read all these posts but here are a couple helpful hints -

1. to remove the old icemaker definitely remove the one lower screw but then unscrew the top two screws only half way. The top screw holes on the old and new icemakers are triangle shaped so the old icemaker will simply lift off the half-unscrewed top screws. This makes reinstallation SO much easier.

2. carefully lower the loose icemaker enough to disconnect the wiring harness from the fridge and remove the old icemaker.

3. On installation the one thing to be careful with is the positioning of the fill tube. It's easier if it's in place when you reconnect the harness of the new icemaker because the harness is only as long as it must be.
4. hang the new icemaker on the half unscrewed top screws, snug them up, install the lower screw and flip the wire ice level sensor arm down.

I didn't even turn the water off because only a working icemaker can turn the water valve on and off.

Plugged in the power to the fridge and within an hour water filled the tray. By morning I had 2-3 batches of fresh ice in the bucket. Super easy.

First removed 3 screws and took out old ice maker, punched out water inlet tube area in new ice maker connected the electric and screwed it back in. Within an hour...heard the ice drop. (I did not do the repair, my boyfriend did, however I think I could have done it.

First 1/4'' nut driver was needed.Then i proceeded
to remove the nut just below the ice maker in a
white bracket. Then i loosen the two nuts at top of
icemaker,enough to lift it off the clips. Then that
allowed me to unplug the plug in rear socket. Then
you plug in the new plug that came with icekaker
and reattach ice maker making shore the two top
clips slide into each other. Do not tighten unto you
incert bottom screw in lower bracket.Make sure
icemaker is push all the way up ,then tighen all
screws.

I first removed the bottom screw then loosened the top two screws about 3 turns lifted an then slide icemaker out a couple inches then used small screwdriver to unclip the wire conector and removed icemaker then pluged new icemaker in and tightened top screws replaced bottom screw lowered metal arm and was done. les than 10 min. it has taken me longer to write this reply than it did to install the icemaker.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

This was an easy repair.

First I turned off the breaker that supplies power to the refrigerator, then I followed instructions to remove the old ice maker. I removed the bottom screw and loosened the two top screws and it came out easily.

The only unexpected problem I ran into was that the connection at the refrigerator end was 'hard wired', i.e., the wiring harness was not removable from the freezer.

After disconnecting the wiring harness from the old ice maker, all I had to do was plug the wiring harness into the new unit, slide it into place, then replace the bottom screw and tighten the two top screws.

Turned the power back on and had ice within 1/2 hour! : )

I just removed three screws from the old ice maker and disconnected a single set of wires. All I had to do was reconnect the new set of wires and screw it back into the side of the freezer. Anybody could do this repair.

Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.

Looking at the instructions it looked like I had to rewire the the plug in the adapter. As it turns out, you don't .Using a screw driver, I released the braket mount and the nut driver loosened the nut holding the tray to the wall. It came right off when you lift it straight up and the wire assembly was exactly the same as the original. All I did was plug in the new ice maker, Hang the assembly on the loosen nuts and tighten again and put the screw back in the bottom bracket that held it in place. I spent longer looking at the instructions than I actually did in the whole replacement time. By morning we had a good amount of ice. EASY>>

The ice maker is held in by three screws. There is an electrical connection. Also, there is a water line to the rear of the unit.
The replacement unit had clear instructions and a selection of parts to match the defective device.
Hint: don't discard the old unit until the new unit is configured for installation.
Turned on the water and the electricity to the fridge, and had ice in several hours.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!