10632 - Instructions

First I cut the gasket-fip with the wire cutters. Then I removed the gasket by pulling it away from the center if the door (not perpendicular to the door). I placed the new gasket over the door, secured the corners first, then pressed the rest of the gasket into place.

The repair to the refrigerator door (lower compartment) stopped the freezer from frosting (upper compartment), and it also reduced the time the compressor runs. However, I have the freezer turned to the lowest possible setting, and it still seems to be quite cold. There may be another issue w/ the unit such as the thermostat.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

We just had to find the trick to put it in where it would catch on and the rest was a piece a cake.

You had to put it in the groove where it would catch and snap it in place and the rest went in
pretty easy.

Replacement was very easy as new ice maker was identical to the old one. Took about 10 minutes.

Removed back panel in the freezer. Removed old fan. Installed new fan and reinstalled back panel.

I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Step 1.
Pay $100.00 for a $10.00 plastic drawer
Step 2.
Remove broken crisper drawer.
Step 3.
Slide in new overpriced crisper drawer.
Step 4.
Write ridiculous instructions on how to get ripped off on a crisper drawer.

changed the starter connected to the compressor

Simply move the appliance for access to the back side. Removed the lower metal access panel, locate the compressor ( black round object ) parts are on the left bottom of the compressor. Simply unplug the parts, and replace with new parts.The hard part was, getting my 72 year old body in position to do the job. As far as getting the right part, a young lady in Nova Scoita is the one to ask for help !! Ordered parts one day, and they were in my hands the next morning!!

First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.

its not that hard to replace. may need help to tilt fridge on one side so you can get to the bottom to remove wheel.Had to undo all four corner screws/bolts to loosen bottom section and slowly pull out base frame which holds the 4 wheels. this frame is also holding the compressor and fan so be careful.replace wheel and slowly put frame back to position and screw back bolts. pull back fridge to upright position. leave unplugged for a day or two to allow gas to come back to normal level as we had tilted it.plug it back and it works.
thanks
Anoop

Freezer freezes and wont defrost. Ice clogs up the coils and the fridge gets hot. Repairman said it was the timer so I replaced that and it didnt fix it. Ordered defrost heater and installed and it is still not fixed. 150$ so far. Should have thrown it away like the repairman suggested.

Removed the bulbs and replaced

The repair was so simple. I removed the old icemaker in about 3 minutes and unpacked and installed the new one is about 10 minutes. It was literally a matter of removing a few screws! Eady to follow instructions!