10420-2 General Electric Range - Instructions

Diane from Kingston, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

The door handle on the over was broken.

I removed the oven door from the range. Removed the broken handle and replaced the new one.

Parts Used:

Door Handle

Baker from Durant, OK
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

Door handle end cap got brittle and broke on oven door.

Slide oven door off slides and put oven door on table. Removed 2 torx-20 screws from top of oven door on the inside. Remove 4 sheet medal screws from the bottom of door 1/4' socket heads. The inside of the door will now separate from the front of door.Now you can see 2 screws on each side of the door handle end caps on 1/4 " socket heads. Remove the 2 screws on which ever side is broken and remove old end cap and side new one on an install 2 screw. When you put door back together there are 2 spring steel spacers that fall off the top 2 screws that hold the inside and outside at the proper space! Parts Select service is EXCELLENT!!!!!

Parts Used:

James from Wiscasset, ME
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set

Was this instruction helpful to you?

The burner bowls were encrusted with grease and spills.

I easily took out the old ones and put in the new ones sent by Part Select. As promised they fit perfectly. Now when my wife cooks there is no more smoke and it does not set off the smoke detector.

Parts Used:

Ed from Canyon City, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Stove door handle broken

Unscrewed the old broken pieces to the handle and put on the new handle, very easy!!!

Parts Used:

Door Handle

Melvette from Stamford, CT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

replace end caps

The video was very helpful.Very easey repair

Parts Used:

Thomas from Glen Island, VA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Replaced All Burner Receptacles After One Failed And Also Replaced Ball Burner Bowls

This installation was for a replacement for one of the burner bowls on the original order. Replacement bowl fits proiperly.

Parts Used:

ROBERT from MECHANICSBURG, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

bowls were worn out

Open the box and inserted the bowls

Parts Used:

frances from winston salem, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Left bracket broken on range oven door handle.

Using a torx screwdriver, I removed the old handle bracket. I had to be careful not to lose a metal spacer that went between the back of the door front panel and the back of the inside door panel. With the door in full open position, I was able to hold this spacer in my thumb and fore finger while I removed the screw. The broken portion of the handle bracket fell to the floor. With the old handle removed, I placed the screw through a hole in the inside panel, through the spacer and through a hole in the front panel. While holding the front pull bar in the right handle bracket, I placed the new bracket on the bar holding it in position on the door and attaching the screw. Easy peasy!

Parts Used:

Roger from De Soto, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

slot that heating element fits was worn down and caused burners to be uneven

replaced with new ones

Parts Used:

Judith from Broadway, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

6" and 8" burner bowl replacement

Slide out burner elements. Remove old burner bowls. Insert new burner bowls and reinstall burner elements.

Parts Used:

Shawn from Lubbock, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner bowls had been used and abused for year gone by in this rental.

Replaced them all. Next I want to replace the burners.

Parts Used:

Diane from Rio Rancho, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

broken door handle

repair was easy and the video was very good. My only problem, I had to go buy a tool, I did not have a nut driver.

Parts Used:

Joan from Schererville, IN
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

The door handle end caps did not fit on to the handle far enough. this caused the screw hole spread to be too wide, Also the new end caps had two nipples outside the bolt holes that the original brackets did not have.

The reason the brackets didn't go on to the handle far enough was there was a molding defect inside one of the brackets. After alot of scraping at the inside of the bracket and lightly tapping with a soft hammer I was able to get the defective bracket on so that the holes lined up to the mounting plate. As for the extra nipples I had two options. Either cut the nipples off or drill some holes in the metal plate that the brackets attach to. I chose the latter. I had to attach the brackets to the plate with extra long screws, reach in under the bracket with a scribe and mark the nipple location on the plate. Then I removed the handle and drilled two holes for each bracket. After some minor adjustments to the holes I was able to attach both brackets and reassemble the oven door.

Parts Used: