Inglis Dishwasher Seals and Gaskets
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Inglis Dishwasher Seals and Gaskets
Your Price
$59.47
In Stock
Inglis Dishwasher Door Gasket With Strike - Black
PartSelect Number PS5136129
Manufacturer Part Number W10542314
This dishwasher door gasket and strike kit is an essential component for maintaining a watertight seal around the dishwasher door and ensuring proper latch operation. The gasket prevents water leakage by forming a tight seal between the door and the tub, while the strike works as a mechanical actuator for the door switch and provides tension for a secure seal. Over time, wear and tear may cause tears, gaps, or cuts in the gasket, leading to leaks. This genuine OEM replacement kit is compatible with select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwashers. For proper installation, unplug the dishwasher or turn off the circuit breaker to ensure safety. Refer to the installation guide or video for step-by-step instructions, and wear protective gloves while replacing the gasket and strike.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Penny from Manchester, MI
The door gasket stuck to the door a pulled out of place after every use
Worked the new gasket into the groove with a smooth screwdriver and my fingers. No leaks and it stays in place. Parts Select had the right part and I got it fast
Read more...
Your Price
$57.38
In Stock
Inglis Dishwasher Door Gasket - Gray
Verified that manifold bearing was not work. It was OK.
Found note that a plugged vent might cause leaking door. Very counterintuitive. Pried off air vent cover. Vent was thouroughly plugged with calcium deposts from steam. Cleaned these out.
Dishwasher no longer leaks. Read more...
PartSelect Number PS11755809
Manufacturer Part Number WPW10509257
This gasket wraps around the sides and top of the dishwasher door and helps seal the door when it is closed to prevent water from leaking from the dishwasher during the washing cycle. If your dishwasher is leaking water, first inspect the seal for food particles near the bottom and sides, and remove it. A buildup can stop the door from closing properly and keeping a tight seal. Check the door gasket for tears, cuts, or wear. If the gasket is damaged, you will need to replace it. Before starting the repair, make sure to disconnect the power to the dishwasher.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Eileen from Salt Lake City, UT
Dishwasher leaking at bottom of door
Installed new door seal. Dishwasher still leaked. Googled the model number and then cleaned the filter at the bottom of the dishwasher, still leaked.Verified that manifold bearing was not work. It was OK.
Found note that a plugged vent might cause leaking door. Very counterintuitive. Pried off air vent cover. Vent was thouroughly plugged with calcium deposts from steam. Cleaned these out.
Dishwasher no longer leaks. Read more...
Your Price
$67.82
In Stock
Inglis Dishwasher Seal
The hardest part was getting the seal, we first ordered from a sears parts store locally. They also told me that everything was included to install it, but they did not include the adhesive, they lost the order via ups and never notified me. I finally called them and they made me go back to the parts store for a refund. I then ordered on parts select and they had it in my hands in 3 days. Read more...
PartSelect Number PS11731683
Manufacturer Part Number W10864081
This is a seal, but you may also know it as a door gasket and it is for your dishwasher. The seal forms a watertight barrier between the door and the dishwasher tub, deterring water from escaping during a wash cycle. If your dishwasher is leaking you will need to replace the seal, as it is likely damaged. The first step should be to check the seal for buildup of food particles near the sides and the bottom of your appliance.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Noelle from Tucker, GA
dishwasher leaking
remove old seal, clean and dry the gap where the new seal will be installed. Apply adhessive, place new seal, then let dry for 24 hrs.The hardest part was getting the seal, we first ordered from a sears parts store locally. They also told me that everything was included to install it, but they did not include the adhesive, they lost the order via ups and never notified me. I finally called them and they made me go back to the parts store for a refund. I then ordered on parts select and they had it in my hands in 3 days. Read more...
Your Price
$26.82
In Stock
Inglis Dishwasher Gasket
PartSelect Number PS11746138
Manufacturer Part Number WP8531323
Water inlet gasket WP8531323 is a water inlet gasket for dishwashers. It ensures a watertight seal at the point where water enters the tub, preventing leaks and maintaining efficient water flow during the wash cycle.
Fixes these symptoms
- Leaking
- Will not fill with water
- See more...
Installation Instructions
J from HARPERSVILLE, AL
Water leak
I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.
Read more...
Your Price
$25.75
In Stock
Inglis Dishwasher Pump Outlet Seal
Once I removed the pump outlet housing I saw that the gasket was out of place almost all the way around. I cleaned around the housing, replaced the gasket and the missing screw.
You need a Torx T-15 for this repair. Note that all of the screws on the housing were loose so you might need to tighten them from time to time.
Be careful not to drip a screw when you are installing it since it's a real hassle to fish it out from under the screen.
Once everything was tightened up, the wash pressure seemed to be much higher. Read more...
PartSelect Number PS11740642
Manufacturer Part Number WP302711
This part is the replacement pump outlet seal or seal ring for your dishwasher. It is made of black rubber and is sold individually. The seal ring creates a seal between the upper compartment of the pump to the pump body. If the seal ring fails, you won’t have good water pressure, and therefore your dishes won’t come clean properly. Improperly cleaned dishes are a good indicator of a bad seal ring. Be sure to disconnect your dishwasher to the water and power sources before you begin this repair. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Charles from Brooklyn, NY
Water leaking out under door
The pump outlet gasket was sticking out and a screw was missing from the pump outlet housing. This was causing water to flood out under the door.Once I removed the pump outlet housing I saw that the gasket was out of place almost all the way around. I cleaned around the housing, replaced the gasket and the missing screw.
You need a Torx T-15 for this repair. Note that all of the screws on the housing were loose so you might need to tighten them from time to time.
Be careful not to drip a screw when you are installing it since it's a real hassle to fish it out from under the screen.
Once everything was tightened up, the wash pressure seemed to be much higher. Read more...
Your Price
$9.62
Special Order
Inglis Dishwasher Drain Cover Gasket
PartSelect Number PS11747044
Manufacturer Part Number WP9740674
Fixes these symptoms
- Leaking
- Noisy
- Not draining
- See more...
Your Price
$46.34
In Stock
Inglis Dishwasher Air Vent Gasket
PartSelect Number PS11745506
Manufacturer Part Number WP8269259
Enhance the functionality of your dishwasher with this genuine OEM Air Vent Gasket from Whirlpool. Compatible with numerous Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwasher models, this component ensures a proper seal between the door panel and the vent duct. Before installation, please ensure to switch off the circuit breaker or unplug your appliance to prevent any potential electrical hazards. In addition, it is recommended to wear work gloves to keep your hands protected during the installation process of this Whirlpool air vent gasket. Please verify your model number for correct part compatibility prior to placing an order. Distinguished by its precise size and shape, this air vent gasket, will optimally fit your chosen model, ensuring efficient operation and longevity of your dishwasher.
Fixes these symptoms
- Leaking
- See more...
Your Price
$11.77
Special Order
Inglis Dishwasher Seal Door Vent
PartSelect Number PS11741357
Manufacturer Part Number WP3379673
Fixes these symptoms
- Leaking
- See more...
Your Price
$76.01
In Stock
Inglis Dishwasher Console Seal
PartSelect Number PS11745508
Manufacturer Part Number WP8269296
This seals at the point where the console attaches to the inner door liner. It is used to create a waterproof seal and prevent leaking.
Fixes these symptoms
- Leaking
- See more...
No Longer Available
Inglis Dishwasher Pump Tub Gasket
PartSelect Number PS384950
Manufacturer Part Number 717000
Introducing this genuine OEM Whirlpool Tub Pump Gasket that is designed to provide the perfect seal at the bottom of your dishwasher around the pump housing. Known for its quality and durability, it effectively prevents any leaks between the circulation pump and the tub. Installation is straightforward, but remember to disconnect the power supply to your dishwasher before getting started. Donning work gloves during installation is recommended for your safety. Trust this Whirlpool Tub Pump Gasket to maintain the efficiency of your dishwasher while ensuring longevity and superior performance.
Fixes these symptoms
- Leaking
- Noisy
- Not draining
- See more...
Installation Instructions
Daniel from Sarasota, FL
leaking from tub above motor
Disconnect unit and remove from under counter. remove lower spray arm, tip over dishwasher on it's back, diconnect wires from motor , unscrew drain fitting rotate motor mounts to and lift pump and motor assembly up and out from inside the dishwasher. thoughly clean all parts during pump disassembly( under running water and a toothbrush works well) . Looking at a parts diagram,and using your memory from disassembly replace the new seals and put it all back together, with patience you can do anything and use common sense.
Read more...