Estate Dishwasher Parts

Estate Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Estate Dishwasher Parts

Your Price
$8.85
  In Stock
Rack Track Stop
★★★★★
★★★★★
(40)
PartSelect Number PS11746591
Manufacturer Part Number WP8565925
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Steven from WASHINGTON, DC
Upper rack wheels had begun to break off. Shoddy design and materials.
I carefully followed the video instructions step by step. They were detailed, clear, and pointed out how to avoid installation mistakes. WIthout the video I would have been tempted to just figure it out myself - ("Hey, I'm a handy guy. How hard could it be, right?"). With the video I sailed right through with no dumb errors. The new rack adjuster wheel set is much sturdier than the Whirlpool original. It made sense to get new rack stops at the same time. Thank you, PartSelect. Read more...
Your Price
$9.11
  In Stock
Rack Adjuster
★★★★★
★★★★★
(28)
PartSelect Number PS11750255
Manufacturer Part Number WPW10204131
Sold Individually.
Installation Instructions
Randy from Glenview, IL
Replacement of broken Rack Assembly Mount with Wheel
The only piece that may be a little difficult to remove here without a tool is the 'Track Stop'. This piece has a couple of clip-like pieces that need to be depressed in order to remove it. A flathead screw driver will do the trick. Once this piece is out and you have popped the Mount off of the Rack, you simply roll the piece out of the track, roll the new one in and snap the new Mount in place, replacing the Track Stop when you are done. VERY EASY! Read more...
Your Price
$7.76
  In Stock
Rubber Washer
PartSelect Number PS11743934
Manufacturer Part Number WP717273
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not drying dishes properly
  • See more...
Installation Instructions
PAUL from ESTES PARK, CO
Unit Wouldn't Work. "Clean" Light Blinking
The unit had power, but the controls would not work. The "clean" light was blinking. I first replaced the control unit, no help. I then used the "just ask" and was told the problem was the heating element and/or the hi-temp thermostat. I replaced both those and used the re-set code pushing the "hi-temp/air dry, hi-temp/air dry" buttons. That did it. Easy parts to locate and replace. It took longer pulling the unit out and putting it back than it did to replace the parts. Read more...
Your Price
$13.68
  In Stock
Mounting Bracket
★★★★★
★★★★★
(12)
PartSelect Number PS11745496
Manufacturer Part Number WP8269145
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.
Fixes these symptoms
Installation Instructions
Judith from Essex, MA
Lost dishwasher brackets
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief! Read more...
Your Price
$9.11
  In Stock
Soap Cup Latch Kit
★★★★★
★★★★★
(8)
PartSelect Number PS382922
Manufacturer Part Number 676413
This soap cup latch kit, used in a dishwasher, will keep the dispenser cover closed. If your dishwasher will not dispense detergent, there is a door latch failure, the dishes are not cleaning properly, or there is leaking, then this kit can be the solution to your symptoms. The tools required for this replacement are a #15 torx bits, a small blade screwdriver, and slip joint pliers. First locate the soap box and remove the latch on both sides. Next step is to remove the screws in the inner door panel and remove the plastic cover at the back. Remove the old latch assembly and add the new one. Make sure to unplug your dishwasher before beginning this installation project.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Steven from Edmond, OK
Latch broke on dishwasher
Look at the exploded parts diagram, that parts select provides on their website.

You have to take off the nine star pointed screws. So you need a special screwdriver or I had a socket set of them and I used a ratchet to make it easier. I think there are nine of them around the base of the door. Then remove the door and set it on the counter. Flip it over and there is a small plastic cover that has to be removed from the back of it, and it is easily removed by gently pulling on it.

Now comes the difficult part. There is a locking piece on it that holds the latch onto the door by interlocking with a piece on the back side of the door. I took a pair of wire snips and just cut the old interlocking piece off. This way I didn't have to try and slide the two interlocking pieces apart.

When you go to put the new piece on before you interlock them make sure they are put on right. Specifically the latch is pointing the right way to seal the detergent door. Otherwise it can be a pain to separate the interlocking pieces again. (which is why I cut it off the old one).

Then you're done. Just put it all back together.
Read more...
Your Price
$8.85
  In Stock
Friction Sleeve
★★★★★
★★★★★
(24)
PartSelect Number PS11745488
Manufacturer Part Number WP8268961
This part helps to keep your door quiet when it opens and closes.
Fixes these symptoms
Installation Instructions
Arthur from YORKTOWN HTS, NY
Door will fall down after opening
unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE. Read more...
Your Price
$8.39
  In Stock
Seal, Lower Sprayarm
★★★★★
★★★★★
(11)
PartSelect Number PS11741334
Manufacturer Part Number WP3376846
This dishwasher lower spray arm seal, or under spray arm bearing ring, is designed with the split by the manufacturer. It is not damaged or defective, and is sourced directly from the original manufacturer. This part is approximately 2 inches in diameter, made of plastic, and is white in color. This part is mounted underneath the dishwasher spray arm and creates a seal between the lower spray arm and the sump housing. To access the seal, remove lower dish rack and unscrew the nut that secures lower spray arm to the remove cover. No tools are required to replace the lower seal on your dishwasher.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
James from Jacksonville, FL
Dishes not clean and lower wash arm wobbled.
Completely removed lower wash arm and replaced bearing ring and seal. Read more...
Your Price
$7.76
  In Stock
Spring, Lid
★★★★★
★★★★★
(10)
PartSelect Number PS11744874
Manufacturer Part Number WP8066018
The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out, or the door is not opening properly, replacing the dispenser spring could be the solution. For this replacement you will need needle nose pliers. First, release the cover on the detergent dispenser, then remove the cover from the shaft it hinges on. Pull the shaft from one side and remove the spring from the shaft. Next, replace with the new spring and engage the two open hooks into the soap cover. Finally, grasp the hook and pull it over tab on the side of the wash cup. Verify that it works properly by opening and closing the cap. Refer to the manual provided by the manufacturer for further instructions.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Not cleaning dishes properly
  • See more...
Installation Instructions
HAROLD from FISHERSVILLE, VA
Worn out spring on detergent release box lid
First, examine very carefully how the old spring relates to the detergent release box lid. Note that the top of the spring has a square-end upside down "U" . This rests on a small ledge on the detergent box. Also note that on either end of the spring is a straight extension of the spring wire. These two "legs" must rest on the inside of the edge of the detergent box. Second, use a flat blade screw driver to pry the LID hinge pin from the mounting "posts. Remove the pin, first noting the position of the spring. Reassemble the spring on the hinge pin in reverse order. Then snap the lid onto the spring using the two mounting "posts". NOTE: I used a very fine needle nose pliers to move the two spring "legs" behind the detergent box edge after I had mounted the lid. Flip the lid down to test if the spring pressure on the lid can be felt. Harold Kitzmann, Fishersville VA Read more...
Your Price
$8.44
  In Stock
Touch-Up Paint - White
★★★★★
★★★★★
(1)
PartSelect Number PS385132
Manufacturer Part Number 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Installation Instructions
Michelle from Richardson, TX
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great. Read more...
Your Price
$60.12
  In Stock
Dishwasher Door Gasket - Gray
★★★★★
★★★★★
(20)
PartSelect Number PS11755809
Manufacturer Part Number WPW10509257
This gasket wraps around the sides and top of the dishwasher door and helps seal the door when it is closed to prevent water from leaking from the dishwasher during the washing cycle. If your dishwasher is leaking water, first inspect the seal for food particles near the bottom and sides, and remove it. A buildup can stop the door from closing properly and keeping a tight seal. Check the door gasket for tears, cuts, or wear. If the gasket is damaged, you will need to replace it. Before starting the repair, make sure to disconnect the power to the dishwasher.
Fixes these symptoms
Installation Instructions
Eileen from Salt Lake City, UT
Dishwasher leaking at bottom of door
Installed new door seal. Dishwasher still leaked. Googled the model number and then cleaned the filter at the bottom of the dishwasher, still leaked.
Verified that manifold bearing was not work. It was OK.
Found note that a plugged vent might cause leaking door. Very counterintuitive. Pried off air vent cover. Vent was thouroughly plugged with calcium deposts from steam. Cleaned these out.
Dishwasher no longer leaks.
Read more...

Appliance Type

Related Parts

Popular Estate Dishwasher Models

Below are the most popular Estate Dishwasher models we have. Enter your model number in the search box to find your model.