Popular Dryer Valves

Your Price
$30.86
  In Stock
Dryer M Series New Style Coil Kit
★★★★★
★★★★★
149 Reviews
PartSelect Number PS334310
Manufacturer Part Number 279834
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. The coils are attached to the dryer gas valve. If the dryer does not heat or heats intermittently, the coil may not be opening the gas valve. Both coils must be operational for the valve to open. No continuity would indicate a defective coil, but they can be intermittent and fail when they get hot. Both coils should be replaced when one of them is broken. This part can break as a result of material fatigue from normal use. This part measures approximately 1 inch in diameter and 1 inch in height, and is constructed of plastic and metal. It comes in black/beige. This part features a 3-terminal boost/hold coil and a 2-terminal secondary coil
Fixes these symptoms
Installation Instructions
Michael from Kirkwood, MO
Gas Dryer would not ignite
1. Removed lint screen and holder frame. Unplugged the electrical cord and closed the gas valve in the line before it goes into the dryer.
2. Removed two bolts at bottom front of machine and took off the bottom front panel.
3. Removed three bolts from black plastic exit vent and took it out to give more room to access everything.
4. removed two wires and screws on the limit thermostat. Did the reverse to place the new one.
5. Removed wires (remembering placement), then holder screw. rotated the Gas Dryer Sensor counter clockwise to release the bottom tab so the sensor can be taken off the flame tube. Did the reverse to place the new one on.
6. Removed the one screw on the gas/flame tube that holds the bracket and igniter inside the flame tube. Removed the wires fro the igniter (remember placement) Slid the whole assembly toward the back of the machine to get the tube off the gas valve then rotated the whole assembly counter-clocwise to release the tab on the left side of the bracket. This was a little tight and had to work with it a bit to get the tab out and slide the whole piece out of the flame tube.
7. Once the tube and igniter were out i removed the scree that holds the igniter and replaced with the new one. Made sure no dust, etc. was in the piece.
8. Did the reverse to place the tube/igniter back into the flame tube.
9. Carefully and forcefully removed the wire connectors to the two coils. These were tough to get off. Removed the two screws that hold the bracket that holds the two coils in place. Slid the coils off the spindles remembering which one has the two wire connection and which one has the three wire connection and the way they went on. Replaced the old with the new. Placed the bracket onto the new coils and made sure the little bumps on the top are in the holes in the bracket. Tightened the screws to hold the coil bracket. Reattached the wire connectors to the coils making sure they go ALL the way back on.
10. Vaccumed everything I could to get lint, dust, etc. out.
11.Replaced the black vent plastic.
12 Made sure the exit vent on the back was not crimped or clogged. Checked the little flap door where the vent goes outside to make sure it opens and closes super easy to no air flow is restricted.
13. For testing I left the bottom panel open. Make sure you closed the door, reconnect the plug and turn the gas valve back on. Hit the go button on autodry or timed dry. The door must be closed to create the closed circulation of the system so the fan sucks the flame into the tube otherwise the flame will not fire deep into the tube and will set off one fo the overheat sensors. After hitting the go button your drum will start to rotate, then a few seconds later you'll hear a click and your igniter will start to burn bright orange. Another click and the gas should flow and ignite.
14. This shows that you've fixed the ignition problem. I just replaced everything I thought that could be wrong in stead of hunting and trial and error. All the parts were about $137 so I thought it was worth making sure.
15. IMPORTANT: If during your test the flame turns off after a little while then turns back on only to turn off again, don't panic. This happened to me as well. I found that you need to run the dryer with wet clothes in the dryer. The wetness in the clothes will keep the autodry sensor from shutting off the dryer since there will be moisture in the exhaust. If it's on timed dry the wet clothes will cool the exhaust air and keep the overheat sensors from turning the heat off. So no heating of dry clothes to get out wrinkles. Just dry the wet clothes. This is all I did and it's been working great so far. Good Luck!
Read more...
Your Price
$21.43
  In Stock
Dryer M Series Ignition Coil Kit
★★★★★
★★★★★
24 Reviews
PartSelect Number PS470049
Manufacturer Part Number 5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the symptoms that this kit could be a solution for are: If there is no heat, not enough heat, or clothes takes too long to dry. In this case, the gas valve coils can be defective and replacing this part will help. Customers rate this project as easy. Refer to the installation diagram for further instructions. For safety, unplug your dryer before repair.
Fixes these symptoms
Installation Instructions
Brett from Monticello, MN
Dryer would heat initially then cool down
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle. Read more...
Your Price
$41.86
  In Stock
Dryer Liquid Propane Conversion Kit
★★★★★
★★★★★
10 Reviews
PartSelect Number PS3493998
Manufacturer Part Number 49572A
This part converts your appliance from Natural Gas to Liquid Propane.
Installation Instructions
Billy from Maryville, TN
cocverting natural gas to propane gas
removed burner installed propane orfice and kit as per instruction sheet. Read more...
Your Price
$62.66
  In Stock
Dryer VALVE
PartSelect Number PS8689119
Manufacturer Part Number 137544800
Your Price
$22.05
  In Stock
Dryer Conversion Kit - NG - LP
★★★★★
★★★★★
4 Reviews
PartSelect Number PS3522299
Manufacturer Part Number 383EEL3002A
This orifice converts your natural gas dryer to operate on liquid propane. This conversion kit is installed in the gas supply system, regulating the flow of gas into the burner, allowing the dryer to heat up and dry your clothes. Orifices naturally degrade with use. You will notice that the orifice has failed or corroded when your dryer fails to properly heat or dry clothes or when yellow flames or plumes of unburnt gas exit the dryer vent. This replacement part is sourced directly from its original manufacturer.
Your Price
$33.69
  In Stock
Dryer M-Series Primary Dual Coil Gas Valve
★★★★★
★★★★★
2 Reviews
PartSelect Number PS268153
Manufacturer Part Number WE4X692
This 'M' series coil is both a boosting as well as a holding coil. It has three terminals.
Installation Instructions
Erik from Newport, ME
Dryer would heat initially, but would not heat throughout entire cycle.
-Removed top panel
-Removed right side panel
-Gas coils were held in together under a metal strap
-Removed 2 screws holding strap
-Unplugged 1 wire harness to each coil
-Removed Primary and Holding coil
-Replace with two new coils, replace strap and plug in each harness
-Replace side, then top panel
-Under 1 hour job...Took 45 minutes to remove/replace panels and only 5 minutes to replace coils.
-Anyone with a little mechanical ability can save $150 in labor and spend just $50 in parts to fix this problem.
-Questions: Erik at elstransport13@gmail.com
Read more...
Your Price
$56.78
  In Stock
Dryer LP CONVERSION KIT
PartSelect Number PS2350027
Manufacturer Part Number PCK4200
Your Price
$24.15
  In Stock
Dryer Conversion Kit - Liquid Propane to Natural Gas
★★★★★
★★★★★
2 Reviews
PartSelect Number PS3524507
Manufacturer Part Number 4948EL4001B
Installation Instructions
Joani from BONNER SPGS, KS
LP to Natural Gas
The installation of the gas orifice was actually simple. Unscrew the old orifice and screw in the correct orifice. Tricky part of the process was accessing the area of the gas valve. Read more...
Your Price
$29.56
  In Stock
Dryer M - Series Secondary Coil - 2 Terminals
★★★★★
★★★★★
8 Reviews
PartSelect Number PS268154
Manufacturer Part Number WE4X693
This part is the replacement main valve coil for your dryer. It is black and white in color and has 2 terminals. It is approximately 1 inch long and 1 inch wide. The main valve coil opens the gas valves while the dryer is running. This coil is used with two coil gas shut off valve assemblies. Be sure to turn off the gas before you begin this repair. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.
Installation Instructions
Erik from Newport, ME
Dryer would heat initially, but would not heat throughout entire cycle.
-Removed top panel
-Removed right side panel
-Gas coils were held in together under a metal strap
-Removed 2 screws holding strap
-Unplugged 1 wire harness to each coil
-Removed Primary and Holding coil
-Replace with two new coils, replace strap and plug in each harness
-Replace side, then top panel
-Under 1 hour job...Took 45 minutes to remove/replace panels and only 5 minutes to replace coils.
-Anyone with a little mechanical ability can save $150 in labor and spend just $50 in parts to fix this problem.
-Questions: Erik at elstransport13@gmail.com
Read more...
Your Price
$26.44
  In Stock
Dryer Natural Gas Orifice for Gas Valve
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11740485
Manufacturer Part Number WP234826
Installation Instructions
Dexter from COUNCIL BLFS, IA
Needed to convert from LPG to Natural Gas
Two parts were needed in order to convert the dry back to Natural Gas. Part Select is usually good, but dropped the ball completely on this one. I received the correct Orifice, but was not asked or told about the need for the part for the regulator so the gas pressure would be changed back to Natural Gas. I found one at a local supplier and finished the switch. I chose to change the belt while in there because the dryer sounded like the belt had a chunk missing with the rhythmic thump. After installing the new, I found that one of the tumble paddles had a penny flopping inside it. One thump per revolution. This is the first in my career that the technician had not left the original orifice and regulator cap attached to the dryer. Read more...

Dryer Valve Brands