Washer Pulleys
Popular Washer Pulleys
Your Price
$60.72
In Stock
Washer Transmission Pulley and Bearing Kit
PartSelect Number PS2003651
Manufacturer Part Number 12002213
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race washer. These genuine Whirlpool parts are plastic and are not sold individually. The kit is used to help the washer drain, and may need to be replaced if the washer is experiencing slow or no spin, will not drain, or has no agitation. The washer will need to be tilted on its back or side to access the bottom. The tools needed to complete this repair are a small flat blade screw driver and a pair of slip joint pliers.
Fixes these symptoms
- Burning smell
- Spinning Issues
- Spins slowly
- See more...
Installation Instructions
James from Hueytown, AL
Washer tub would not spin, pump would empty water from tub.
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
Read more...
Washer Pulley,Idle
PartSelect Number PS3523032
Manufacturer Part Number 4560EL3001A
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Mark from OSHKOSH, WI
1 of 4 Drum Rollers Froze Preventing drum rotation.
Replaced idle pulley wheel, worn drum belt and all 4 rollers (1 frozen) due to dryer age. Site video re general disassembly/re-assembly easily adapted to this model and very helpful with exception of replacement of drum rollers. New rollers received (AGM75510755) were pre-mounted on included shafts. This required removal of existing roller shafts to replace with new shaft/roller units. Site video shows placing a new roller on existing shafts after removing a plastic retaining clip. New roller/shaft assembly is a better option and fortunately I did not order extra retainer clips! Rear drum roller shafts have small carved out space to fit a box end wrench to remove shaft nut. Watch out for sharp edges on internal steel parts!
Read more...
Washer Pulley Assembly,Motor
PartSelect Number PS3523033
Manufacturer Part Number 4561EL3002A
Fixes these symptoms
- Noisy
- See more...
Washer Plastic Motor Pulley
PartSelect Number PS11738804
Manufacturer Part Number WP21001108
This motor pulley is only an inch high and is two and a half inches in diameter. It is all black in color and is made entirely of plastic.
Fixes these symptoms
- Burning smell
- Will not agitate
- Will not drain
- See more...
Installation Instructions
Kevin from Berwick, ME
worn belt & burnt motor pulley
First, I looked at the site for instructions on what was wrong, it explained in full detail what and how to remove and replace. We called a local Maytag dealer and told them the part number that the site told us to order and they told us we needed a whole new motor with the plastic motor pulley. they told us the part does not come separate, so we went back to the site and ordered a $6.00 part and paid a small s/h charge and when it came in we went back to the site to see how to put it back together and the instructions were perfectly awesome. The $6 part is what we actually needed not the $178 complete motor that the dealer told us we had to buy. Thanks for this wonderful site it saved us lots of money. this is the 3rd time we order from this site and the instructions we correct all 3 times, I would recommend this site to all who has a home with repairs! Thank you for putting a well useful site together.
Read more...
Your Price
$99.18
In Stock
Washer Drum Drive Pulley
PartSelect Number PS11745017
Manufacturer Part Number WP8182650
This drive pulley attaches to the back of the washers drum.
Fixes these symptoms
- Will not agitate
- See more...
Installation Instructions
Francis from Rochester, NY
Washer made loud banging noise during spin cycle
I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the washer was back in service.
Read more...
Washer Idler Pulley Wheel
PartSelect Number PS11742250
Manufacturer Part Number WP40045001
This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.
Fixes these symptoms
- Burning smell
- Noisy
- Spins slowly
- See more...
Installation Instructions
Lucas from Nuevo, CA
Need it a new pulley and belt
I did the repair all by my self and just payed for the parts.
Read more...
Washer DRIVE PULLEY
PartSelect Number PS1482349
Manufacturer Part Number WH07X10019
Installation Instructions
howard from LA FAYETTE, GA
Clutch drive wore out and was making a clunking noise during operation.
I removed the front cover and the top cover. Then I unplugged all the,wires and removed the hangers. Then removed tub and drum together out the front. After beating on the tub nut for 2 hours and drenching it in liquid wrench I realized that the,tub nut was not going to release. Yes I was turning it clockwise. I bring out my chisel and hammer. After removing the,center shaft I chisel the,tube inward till I could get to the nut. Then I chisel the,tub nut into 3 pieces. It then appeared why it wasn't coming loose,earlier the powders,had gotten below the nut and had it cemenred on. So those youtube videos,are helpful to an extent.
Read more...
Washer Pulley
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years. Read more...
PartSelect Number PS2020240
Manufacturer Part Number 22002315
Installation Instructions
Loanne from W BROOKFIELD, MA
Washer was so loud in the spinning cycle it sounded like a jet was taking off
We took the washer completely apart. Replaced the bearings, pulley andbelt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years. Read more...