My Orders
Amana Washer Pulleys
GET YOUR OFFICIAL Amana PARTS TO ENSURE VICTORY
Popular Amana Washer Pulleys
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging the drive motor to rotate the washer basket. The kit includes the clutch assembly, cam ring, spring, basket drive gear, pulley, and mounting nut. Replacing this component can resolve issues such as noisy operation, slow or failed spinning, poor agitation, and excessive moisture in clothes after a cycle. In some cases, a burning smell may also indicate a failing clutch. Installation requires basic tools and should be performed with the appliance disconnected from power. Compatibility should be confirmed using your washer’s model number.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging the drive motor to rotate the washer basket. The kit includes the clutch assembly, cam ring, spring, basket drive gear, pulley, and mounting nut. Replacing this component can resolve issues such as noisy operation, slow or failed spinning, poor agitation, and excessive moisture in clothes after a cycle. In some cases, a burning smell may also indicate a failing clutch. Installation requires basic tools and should be performed with the appliance disconnected from power. Compatibility should be confirmed using your washer’s model number.
Installation Instructions
Jerry from WALLA WALLA, WA
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read more
and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Read less
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race washer. These genuine Whirlpool parts are plastic and are not sold individually. The kit is used to help the washer drain, and may need to be replaced if the washer is experiencing slow or no spin, will not drain, or has no agitation. The washer will need to be tilted on its back or side to access the bottom. The tools needed to complete this repair are a small flat blade screw driver and a pair of slip joint pliers.
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race washer. These genuine Whirlpool parts are plastic and are not sold individually. The kit is used to help the washer drain, and may need to be replaced if the washer is experiencing slow or no spin, will not drain, or has no agitation. The washer will need to be tilted on its back or side to access the bottom. The tools needed to complete this repair are a small flat blade screw driver and a pair of slip joint pliers.
Installation Instructions
James from Hueytown, AL
Washer tub would not spin, pump would empty water from tub.
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
This drive pulley attaches to the back of the washers drum.
This drive pulley attaches to the back of the washers drum.
Installation Instructions
Francis from Rochester, NY
Washer made loud banging noise during spin cycle
I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the
... Read more
washer was back in service.
Read less
This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.
This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.
Installation Instructions
Lucas from Nuevo, CA
Need it a new pulley and belt
I did the repair all by my self and just payed for the parts.
This genuine drive/spinner pulley is a key component that connects the motor’s drive system to the spin basket, enabling high-speed rotation for effective water extraction during the spin cycle. Designed for durability and precision, it helps resolve issues such as poor spinning, wet clothes, or loud noises caused by a worn or damaged pulley. Installation restores proper performance and reduces vibration, ensuring smooth and efficient operation.
This genuine drive/spinner pulley is a key component that connects the motor’s drive system to the spin basket, enabling high-speed rotation for effective water extraction during the spin cycle. Designed for durability and precision, it helps resolve issues such as poor spinning, wet clothes, or loud noises caused by a worn or damaged pulley. Installation restores proper performance and reduces vibration, ensuring smooth and efficient operation.
Installation Instructions
Loanne from W BROOKFIELD, MA
Washer was so loud in the spinning cycle it sounded like a jet was taking off
We took the washer completely apart. Replaced the bearings, pulley and
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This motor pulley is only an inch high and is two and a half inches in diameter. It is all black in color and is made entirely of plastic.
This motor pulley is only an inch high and is two and a half inches in diameter. It is all black in color and is made entirely of plastic.
Installation Instructions
Kevin from Berwick, ME
worn belt & burnt motor pulley
First, I looked at the site for instructions on what was wrong, it explained in full detail what and how to remove and replace. We called a local Maytag dealer and told them the part number that the site told us to order and they told us we needed a whole new motor with the plastic motor pulley. they told us the part does not come sepa
... Read more
rate, so we went back to the site and ordered a $6.00 part and paid a small s/h charge and when it came in we went back to the site to see how to put it back together and the instructions were perfectly awesome. The $6 part is what we actually needed not the $178 complete motor that the dealer told us we had to buy. Thanks for this wonderful site it saved us lots of money. this is the 3rd time we order from this site and the instructions we correct all 3 times, I would recommend this site to all who has a home with repairs! Thank you for putting a well useful site together.
Read less
This helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.
This helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.
