Amana Washer Springs and Shock Absorbers | Replacement Parts & Accessories | PartSelect

Popular Amana Washer Springs and Shock Absorbers

Your Price
$3.52
Suspension Spring
PartSelect Number PS11743345
Manufacturer Part Number WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or has stretched out and lost its spring, it could cause the load to be off-balance which can lead to excessive shaking, moving, noise, and leaks. For this repair, you will need a 1/4 nut driver, a putty knife, a flat blade screw driver, and a pair of needle nose pliers. Disconnect the power supply, fill hoses, and drain hose to give you safe and easy access (have a container nearby for water left in drain hose). This item is sold individually.
Fixes these symptoms
Leaking
Noisy
Shakes and moves

See more...
Installation Instructions
Brian from Seattle, WA says,

Washer tub slammed into washer body during spin cycle
If you load a washing machine unevenly, it will spin out of balance. But our washer seemed to make noise during the spin cycle regardless of how the load was distributed. I suspected that the suspensi...read more

Your Price
$4.97
Suspension Rod Support
PartSelect Number PS3502189
Manufacturer Part Number W10440729
These parts are the replacement suspension rod supports for your washer. They are made of plastic and are approximately 1 ½ inches in diameter. This package will come with an 8-piece set of suspension rod supports. There are 4 of each type. Be sure to consult the parts diagram for your washer for the complete list of parts included. The suspension rod supports help secure the suspension rods, so your washer operates smoothly. If your dryer shakes, moves, or is noisy during operation, you may need to replace the suspension rod supports. These are OEM parts sourced directly from the manufacturer.
Fixes these symptoms
Noisy
Shakes and moves


Installation Instructions
Joseph from PERKINS, GA says,

Washer was off balance during spin cycle. The suspension piece broken.
Replaced 1 of 4 of the suspension bushing. Works great....read more

Your Price
$53.45
Washing Machine Suspension Rod Kit
PartSelect Number PS11703290
Manufacturer Part Number W10780048
Washing machine tub suspension rod kit,. Set of 4 rods, 4 suspension balls and 4 bushings. The suspension rods help to dampen the movement of the washer tub. If one or more of the suspension rods are broken, the washer will vibrate or shake.
Fixes these symptoms
Noisy
Shakes and moves


Installation Instructions
Terry from Homosassa, FL says,

Violent shacking in spin mode.
Watched a video on the internet....read more

Your Price
$5.10
SPRING
PartSelect Number PS3497596
Manufacturer Part Number W10400895
Tub centering spring - Included 2 springs
Fixes these symptoms
Noisy
Shakes and moves


Installation Instructions
Timothy from E PALESTINE, OH says,

WASHER ON SPIN CYCLE WOULD SHAKE, MAKE NOISE AND WALK ACROSS FLOOR
FOLLOWED VIDEO INSTRUCTIONS, UNPLUGGED AND REMOVED WATER LINES AND DRAIN, REMOVED HARNESS COVER PLATE. MOUNT SCREWS AND TOP, UNHOOKED SUSPENSION RODS(FOUND THEY HAD LEFT OUT TOP SPRINGS FROM TUB TO S...read more

Your Price
$5.09
Tub Spring
PartSelect Number PS11751118
Manufacturer Part Number WPW10250667
This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of the motor on the front of the front-load washer so the washer tub sits straight and even during the spin cycle. You may need to replace the spring if tub is sitting tilted forward. A broken spring will result in the tub being off-balance during the spin cycle which can cause further damage to washer parts. It is recommended to check all suspension springs as they often wear at the same rate. Tools needed for repair are a Phillips screw driver, flat blade screw driver, and a pair of pliers.
Fixes these symptoms
Leaking
Noisy
Shakes and moves

See more...
Installation Instructions
RICHARD from PHILA, PA says,

Replace Water Pump Coupling
Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump. ...read more

Your Price
$5.83
Suspension Spring
PartSelect Number PS11738823
Manufacturer Part Number WP21001598
This suspension spring is 7 inches in length, and is sold individually. It is a good idea to replace all six springs at once to maintain the same tension level. To complete this repair you will need a putty knife, 5/16ths nut driver, and a pair of pliers. The springs are located underneath the washer bin, to replace them you will need to remove the main top and front panel of the washing machine.
Fixes these symptoms
Noisy
Shakes and moves


Installation Instructions
David from Butler, PA says,

Washer jumping in spin cycle (white flakes under the washer)
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take...read more

Your Price
$47.70
Shock Absorber
PartSelect Number PS11723173
Manufacturer Part Number W10822553
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber (part number W10822553) is for washers. Shock absorber W10822553 absorbs the vibrations and movements of the outer washer tub. Unplug the washer before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
Noisy
Shakes and moves


Installation Instructions
SCOTT from COLCHESTER, CT says,

shocks showing their age
Overall, the install was easy.
Just a matter of getting yourself to get it done.
The video on the removal / install procedures was most helpful.
The front shocks were completed very qui...read more

Your Price
$6.34
Snubber Ring
PartSelect Number PS11738845
Manufacturer Part Number WP21002026
The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome assembly. If during your spin cycle you notice your washer jumping and making loud whirring noises, you may need to replace your snubber ring. The tools you will need for this repair include: a putty knife, a 5/16 nut driver, a 1/4 inch nut driver, a 3/8 socket and a ratchet, a small flat blade screwdriver, a pair of locking pliers, and a pair of slip joint pliers.
Fixes these symptoms
Noisy
Pumps but will not spin
Shakes and moves

See more...
Installation Instructions
David from Butler, PA says,

Washer jumping in spin cycle (white flakes under the washer)
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take...read more

Your Price
$7.77
Tub Wear Pads - Package of 3
PartSelect Number PS334620
Manufacturer Part Number 285744
This package of pads contains three brown tub wear pads.
Fixes these symptoms
Noisy
Shakes and moves


Installation Instructions
Dexter from Milwaukie, OR says,

Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part B...read more

Your Price
$6.11
Leveling Spring
PartSelect Number PS394983
Manufacturer Part Number 8316845
This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.
Fixes these symptoms
Noisy
Shakes and moves


Installation Instructions
john from middle river, MD says,

Machine rocking about like crazy on spin
Took some online research to figure out how to get the cabinet off. Once inside I fitted the wear pads which were a breeze to remove using a knife blade to pry them up and removing them using the scre...read more