Amana Washer Motors

Amana Appliance Parts
Shop By Part Type

Popular Amana Washer Motors

Your Price
$27.04
  In Stock
Direct Drive Motor Coupling
★★★★★
★★★★★
(156)
PartSelect Number PS1485646
Manufacturer Part Number 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Fixes these symptoms
Installation Instructions
Jeff from Wayne, NJ
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Read more...
Your Price
$156.79
  On Order
Drain Pump Kit
★★★★★
★★★★★
(53)
PartSelect Number PS1485610
Manufacturer Part Number 280187
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
Fixes these symptoms
Installation Instructions
Donald from Wichita, KS
Washer would not drain ,F02 and SUD code displaying
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
Read more...
Your Price
$150.16
  On Order
Motor with Pulley
★★★★★
★★★★★
(6)
PartSelect Number PS11738839
Manufacturer Part Number WP21001950
This motor is a 2 speed, 1/2 HP, 120V, 60Hz.
Fixes these symptoms
  • Burning smell
  • Noisy
  • Pumps but will not spin
  • See more...
Installation Instructions
Michael from Warminster, PA
The belt and pulley on the drive motor broke
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed.
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
Read more...
Your Price
$236.26
  In Stock
2-Speed Drive Motor - 60Hz 120V
★★★★★
★★★★★
(7)
PartSelect Number PS11743427
Manufacturer Part Number WP661600
This is a 2-speed drive motor for your washing machine. The motor rotates the spin basket when the washing machine is in spin or tumbling mode. You will likely need to replace the motor if you are experiencing burning smells or your washer will not start. The tools you will need to make this repair include a number two Phillips screwdriver, a flat-blade screwdriver, and a 5/16 nut driver.
Fixes these symptoms
  • Burning smell
  • Pumps but will not spin
  • Will not agitate
  • See more...
Installation Instructions
Lowell from Dover, DE
Washer had water leak in lower front and would not drain.
Laid the washer on its back and found leak in water pump. Found out it was caused by vibration from motor with bad bearing. Removed pump and motor which were held on by clips. Both were removed and replaced without removing cabinet from machine. Read more...
Your Price
$303.74
  In Stock
MOTOR Assembly - 1/3 HP
PartSelect Number PS11726282
Manufacturer Part Number W10832724
Your Price
$267.79
  In Stock
Drive Motor
PartSelect Number PS11757089
Manufacturer Part Number WPW10677715
Your Price
$348.04
  In Stock
Drive Motor
PartSelect Number PS11749532
Manufacturer Part Number WPW10171902
This part works in conjunction with the pump to aid in spinning and draining.
Your Price
$279.68
  In Stock
MOTOR-DRVE
PartSelect Number PS11727863
Manufacturer Part Number W10836348
Your Price
$210.30
  In Stock
Drive Motor with Capacitor
PartSelect Number PS2003589
Manufacturer Part Number 12002133
Your Price
$443.33
  In Stock
MOTOR 240
PartSelect Number PS11738824
Manufacturer Part Number WP21001637

Related Parts