Amana Washer Valves
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Amana Washer Valves
Your Price
$32.63
In Stock
Amana Washer Water Inlet Valve With Mounting Bracket
compoments and reassembled.
Test run machine. Ran like new! Read more...
PartSelect Number PS334646
Manufacturer Part Number 285805
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Don from Wyoming, MN
Washer stopped at rinse cycle
Removed the top and back panels. Replacedcompoments and reassembled.
Test run machine. Ran like new! Read more...
Your Price
$66.77
In Stock
Amana Washer Water Inlet Valve
PartSelect Number PS12349267
Manufacturer Part Number W11210459
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
- Cycle Not Advancing
- Leaking
- No hot or cold water
- See more...
Installation Instructions
Patricia from MURPHYSBORO, IL
Water would not fill the washer except for 4 inches.
Once we put in the new Water Inlet Valve, the auto sensor works now and I can wash any size load
Read more...
Your Price
$60.51
In Stock
Amana Washer Water Inlet Valve With Thermistor
PartSelect Number PS11749042
Manufacturer Part Number WPW10144820
This part is used to help control and balance the water temperature flowing in to the washer tub.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Barb from Blackriver Falls, WI
Your Price
$56.33
In Stock
Amana Washer Water Inlet Valve
PartSelect Number PS11745050
Manufacturer Part Number WP8182862
This dual-coil water inlet valve is a genuine OEM replacement designed to regulate the flow of hot and cold water into your washing machine. It connects directly to the appliance’s water lines and distributes water to the appropriate dispensers based on cycle settings. Engineered for compatibility with select Whirlpool, Maytag, KitchenAid, and other associated brand models, this valve ensures accurate water temperature control and efficient filling. Common symptoms of a faulty valve include water leaks or improper filling. Installation requires disconnecting power and water supply for safety. Sold individually.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Jerry from Keenes, IL
washing machine giving f20 error code
removed washer top, checked supply hoses and inlet valve to make sure not clogged, replaced valve and while already there replaced flowmeter, reinstall top and hoses and checked machine operation, machine working fine and wife thinks i am her hero
Read more...
Your Price
$61.55
In Stock
Amana Washer Water Inlet Valve
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.
5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished! Read more...
PartSelect Number PS11773194
Manufacturer Part Number W11038689
This is an inlet valve for various washing machines. Inlet valves are responsible for opening and closing as needed, to allow water to enter the washer during the washing cycle. This inlet valve features a hot and cold-water valve, as well as the necessary wire harness to easily plug it in. Since inlet valves are an electrically controlled solenoid valve, they can fail either due to electrical failure such a short, or after long, extended use. If your inlet valve fails, your washer will likely relay an error code, or it simply will not wash your clothes due to the lack of water, and the valves will need to be replaced. Replacing this valve will require a screwdriver and/or socket wrench, and some disassembly of your washer will be necessary. This inlet valve is an individually sold OEM part and does not come with any accessories or other parts.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
melinda from HARROGATE, TN
Water would not stop flowing.
*be sure to turn water off, unplug machine, and unscrew the water hoses from the rear of the washer.1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.
5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished! Read more...
Your Price
$72.00
In Stock
Amana Washer Water Inlet And Valve Assembly
PartSelect Number PS11757114
Manufacturer Part Number WPW10683603
This water inlet valve is a key component in top-load washing machines, responsible for regulating the flow of hot and cold water into the appliance. It electronically opens and closes to deliver the correct amount of water, balances temperature for each cycle, and helps maintain proper water levels. Constructed from durable, high-quality materials, the valve is designed to withstand frequent use and prevent issues such as overfilling, insufficient water flow, or leaks. Replacing a faulty valve can resolve symptoms like the washer not filling, continuous water flow, uneven temperature control, or water leakage from the rear of the unit, restoring efficient and safe operation.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Armand from WESTPORT, MA
Water inlet nozzle was stripped and leak
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one
Read more...
Your Price
$74.08
In Stock
Amana Washer Valve
1. Unplug washer
2. Close Hot and Cold water valves
3. Remove top cover of the machine by taking out 3 screws in the top back. Slide top back and remove.
4. Water Inlet Valve is located on the back left side, remove tubing using a nutdriver to loosen the hose clamps.
5. Water Inlet Valve is removed by removing the screw in the back of the valve and turning the valve clockwise a little.
Replace with the new one, connect hoses, put cover back on, open valves, plug it in.
6. Ran washer and Fabric Softener dispenser now works Read more...
PartSelect Number PS17216730
Manufacturer Part Number W11688995
Introducing the Whirlpool Double Water Inlet Valve. This genuine OEM part is designed for optimal, reliable operation in a variety of washing machines. Not only is this valve perfect for Whirlpool models, but its versatility extends to KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef appliances. It's important to remember that while parts may share similar appearances, their sizes and shapes may vary slightly. Therefore, kindly check if this part is suitable for your model before making a purchase decision. Ensure optimal performance for your washer with this quality Whirlpool Double Water Inlet Valve.
Fixes these symptoms
- Does not dispense fabric softener or detergent
- Leaking
- No hot or cold water
- See more...
Installation Instructions
Frederick from OSWEGO, NY
Fabric Softener dispenser would not drain out
Replaced the Whirlpool washer water inlet valve. 1. Unplug washer
2. Close Hot and Cold water valves
3. Remove top cover of the machine by taking out 3 screws in the top back. Slide top back and remove.
4. Water Inlet Valve is located on the back left side, remove tubing using a nutdriver to loosen the hose clamps.
5. Water Inlet Valve is removed by removing the screw in the back of the valve and turning the valve clockwise a little.
Replace with the new one, connect hoses, put cover back on, open valves, plug it in.
6. Ran washer and Fabric Softener dispenser now works Read more...
Your Price
$93.60
In Stock
Amana Washer Water Inlet Valve Assembly
PartSelect Number PS12349269
Manufacturer Part Number W11210463
This is a water inlet valve for models of Whirlpool washing machines. The water inlet valve is designed to regulate and control the water entering the appliance depending on the cycle, using an electrical device called a solenoid. This water inlet valve features two inlets, one for hot water and one for cold, as well as a wire harness to power and control the electric solenoid of each. If your washer is having issues with filling, the inlet valve is likely bad or potentially worn out and in need of replacement. Replacing this valve will require a screwdriver, wrench, and pliers. This water inlet valve is an OEM part from Whirlpool and is sold individually.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
John from SAINT JOSEPH, MI
Leaking water inlet valve assembly
Remove upper rear panel with drill driver and 1/4" nut driver bit. using the angle bit holder and torx bit remove the two screws holding the assembly in place. Slide out the old assembly and disconnect the wiring harness at the machine. Slide new assembly in place. While holding it down start both screws by hand, then use the driver/angle holder to tighten screws. Reattach the wiring harness and rear plate(s).
Read more...
Your Price
$79.98
In Stock
Amana Washer Water Inlet Valve
PartSelect Number PS1583805
Manufacturer Part Number 205613
This is a water inlet valve which is used in washing machines. The valve controls and monitors the flow of water into the washer. It has a multi-mount bracket and outlet adaptor. The tools needed for this repair are: a 5/16 nut driver, 1/4 nut driver, and a small flat blade screwdriver. If cold water does not flow into washer, or the washing machine will not fill with hot water, replacing the valve can be the solution. To gain access to the water valve, locate the back of the washer and remove the hot and cold hoses, as well as the whole assembly. Next, remove the four wires and loosen up the clamp. After removing the old valve, replace it with the new one and reconnect the wires and hose. Remember to disconnect the washer from the power source before starting this project.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Brian from El Cajon, CA
Cold water valve only opened to a trickle
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outlet hose and pull off the outlet hose. I reversed the steps to install the new assembly and the total repair took about 10 minutes.
Read more...
Your Price
$56.33
In Stock
Amana Washer Water Inlet Valve And Thermistor Assembly
Unplug the washer.
Turn the water off and unscrew the hoses from the inlet.
Unsnap the end caps from the top control panel.
Remove the exposed screws from each end of the panel (#2 Phillips).
Pull the panel out of the way and pop out the two retaining clips that hold the back of the machine to the cabinet. They are located under the control panel.
Remove the mounting screw from the valve assembly (1/4-inch driver).
Pull the back away from the cabinet far enough to remove the valve, but don't let the wires get cut.
Disconnect the wires. To unplug the solenoid connectors, lift the long tab with a screwdriver.
Disconnect the water outlet hose.
Connect the wires and hose to the new valve assembly. The red connector goes to the hot water valve. The thermistor wires (the two individual connectors) can be connected to either terminal. It does not matter if they are reversed.
Put the valve back in place and install the screw.
Hook up and turn the water on.
Plug in the machine and test the valve.
Unplug the power and reinstall the back and the control panel. The back-to-cabinet clips can be snapped back in place easily. Read more...
PartSelect Number PS11742194
Manufacturer Part Number WP3979346
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Pat from Hilliard, FL
Post drip from water inlet
To replace the inlet solenoid valve/thermistor assembly: Unplug the washer.
Turn the water off and unscrew the hoses from the inlet.
Unsnap the end caps from the top control panel.
Remove the exposed screws from each end of the panel (#2 Phillips).
Pull the panel out of the way and pop out the two retaining clips that hold the back of the machine to the cabinet. They are located under the control panel.
Remove the mounting screw from the valve assembly (1/4-inch driver).
Pull the back away from the cabinet far enough to remove the valve, but don't let the wires get cut.
Disconnect the wires. To unplug the solenoid connectors, lift the long tab with a screwdriver.
Disconnect the water outlet hose.
Connect the wires and hose to the new valve assembly. The red connector goes to the hot water valve. The thermistor wires (the two individual connectors) can be connected to either terminal. It does not matter if they are reversed.
Put the valve back in place and install the screw.
Hook up and turn the water on.
Plug in the machine and test the valve.
Unplug the power and reinstall the back and the control panel. The back-to-cabinet clips can be snapped back in place easily. Read more...
Related Amana Washer Parts
- All Amana Washer parts
- Amana Washer Agitators
- Amana Washer Bearings
- Amana Washer Belts
- Amana Washer Brackets and Flanges
- Amana Washer Caps and Lids
- Amana Washer Circuit Boards and Touch Pads
- Amana Washer Dispensers
- Amana Washer Doors
- Amana Washer Drums and Tubs
- Amana Washer Hardware
- Amana Washer Hinges
- Amana Washer Hoses and Tubes
- Amana Washer Knobs
- Amana Washer Latches
- Amana Washer Legs and Feet
- Amana Washer Motors
- Amana Washer Panels
- Amana Washer Power Cords
- Amana Washer Pulleys
- Amana Washer Pumps
- Amana Washer Seals and Gaskets
- Amana Washer Springs and Shock Absorbers
- Amana Washer Switches
- Amana Washer Transmissions and Clutches
- Amana Washer Wire Plugs and Connectors