Amana Washer Pumps

Amana Appliance Parts
Shop By Part Type

Popular Amana Washer Pumps

Your Price
$128.50
  In Stock
Washer Drain Pump
★★★★★
★★★★★
(80)
PartSelect Number PS11757304
Manufacturer Part Number WPW10730972
This is a manufacturer-approved replacement drain pump for your washing machine. To complete this repair you will need a 1/4 inch nut driver, 5/16ths nut driver, a flat blade screwdriver, and a pair of pliers. Make sure to disconnect power to the washer before beginning this repair.
Fixes these symptoms
  • Burning smell
  • Engine runs but does not pump water
  • Leaking
  • See more...
Installation Instructions
Andrew from St.Louis, MO
F 21 error
Removed the front panel unplugged
The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
Read more...
Your Price
$55.27
  On Order
Drain Pump
★★★★★
★★★★★
(18)
PartSelect Number PS11756700
Manufacturer Part Number WPW10605427
Fixes these symptoms
Installation Instructions
JASON from HILLIARD, FL
Drain pump was cracked
Turned washer on its side. Pulled the bottom plate off. Then unplugged the electrical lines. Then unbolted the drain pump and bolted the new drain pump in. Then reversed the process. Read more...
Your Price
$175.99
  On Order
Drain Pump Kit
★★★★★
★★★★★
(42)
PartSelect Number PS1485610
Manufacturer Part Number 280187
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
Fixes these symptoms
Installation Instructions
Donald from Wichita, KS
Washer would not drain ,F02 and SUD code displaying
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
Read more...
Your Price
$99.33
  In Stock
Washer Drain Pump
★★★★★
★★★★★
(22)
PartSelect Number PS11741803
Manufacturer Part Number WP35-6780
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If your machine is not draining properly or if it is noisy and shakes during operation, you may need to replace the drain pump. This is a redesigned part. The pump now mounts on to the base of the washer. This product is made of white plastic and has a metal center. Before you can replace the drain pump, you will have to disengage the drive belt under the machine. To reach the drain pump you will need to remove the access panel on the backside of the washing machine.
Fixes these symptoms
Installation Instructions
Ranse from Layton, UT
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it. Read more...
Your Price
$127.92
  In Stock
Drain Pump - 120V 60Hz
★★★★★
★★★★★
(9)
PartSelect Number PS11751719
Manufacturer Part Number WPW10276397
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time
Fixes these symptoms
Installation Instructions
REED from BUCHANAN, NY
Wouldn’t drain pump made loud noise
Removed old drain pump and found a sock in the inlet - must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues Read more...
Your Price
$60.57
  In Stock
PUMP-WATER
★★★★★
★★★★★
(8)
PartSelect Number PS11757016
Manufacturer Part Number WPW10661045
Fixes these symptoms
Your Price
$140.50
  In Stock
Drain Pump - 120V 60Hz
★★★★★
★★★★★
(11)
PartSelect Number PS11741568
Manufacturer Part Number WP34001340
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: Pump only, mounting bracket is NOT included.
Fixes these symptoms
Installation Instructions
Robert from El Paso, TX
Coins had been pulled into the pump, breaking blades and cracked casing.
First I unplugged the washer and removed the back cover plate of the washer. I drained the pump and drainage lines. I then removed the two hose clamps and removed the connecting hoses. I removed the electrical connection. I loosened the three mounting bolts holding the mounting plate holding the pump. Once out, I could remove the pump from the plate and replaced it with the new part. I remounted the mounting plate, attached the hoses and clamps. I reattached the electrical connection and the back plate to the washer.


The Maytag is well designed and the parts are easy to reach. At least from this experience, the machine was designed with efficient repairs in mind. This is a sign of a well made machine.
Read more...
Your Price
$140.92
  In Stock
Drain Pump - 120V 60Hz
★★★★★
★★★★★
(8)
PartSelect Number PS11740556
Manufacturer Part Number WP25001052
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
Fixes these symptoms
Installation Instructions
Deborah from Westfield, MA
Old Pump Stopped Draining The Machine- Impeller In Pump Wore Out
First- I unplugged and completely drained machine of water by putting hose at ground level near drain . Second- removed back plate to washer saving all hardware. Third- disconnected in and out hose to pump. Twisted pump gently as to pop it out of slots in bottom of machine. Fourth- disconnected wires to old pump hooked to new pump replaced pump, replaced hoses- tested machine then replaced back plate of machine. Done. Read more...
Your Price
$180.07
  On Order
Drain Pump
PartSelect Number PS11754106
Manufacturer Part Number WPW10391443
Fixes these symptoms
Your Price
$163.63
  In Stock
Pump, Drain- Complete Assembly
PartSelect Number PS11749615
Manufacturer Part Number WPW10175948
The water pump is what your washer uses to remove the water from the wash tub.
Fixes these symptoms

Related Parts