Amana Washer Hardware

Find your part

Enter your model number or a part number and click "Search"
Need help finding your model number?
Amana Appliance Parts
Shop By Part Type

Popular Amana Washer Hardware

Your Price
$6.80
  In Stock
Agitator Bolt
★★★★★
★★★★★
(9)
PartSelect Number PS11741866
Manufacturer Part Number WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Fixes these symptoms
  • Leaking
  • Marks left on clothes
  • Spins slowly
  • See more...
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go. Read more...
Your Price
$7.68
  In Stock
Thrust Washer
★★★★★
★★★★★
(2)
PartSelect Number PS11740482
Manufacturer Part Number WP233520
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.
Fixes these symptoms
Installation Instructions
Chris from Hopedale, MA
Drum not centered , clothes getting stuck in dryer
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it. Read more...
Your Price
$7.68
  In Stock
Hose Clamp
★★★★★
★★★★★
(1)
PartSelect Number PS11743008
Manufacturer Part Number WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Fixes these symptoms
Installation Instructions
jeff from lindenhurst, IL
Washing Machine was leaking water
Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years! Read more...
Your Price
$7.68
  In Stock
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...
Your Price
$7.68
  In Stock
Screw, 8-16 x 1.000
PartSelect Number PS11746167
Manufacturer Part Number WP8533953
Sold individually.
Installation Instructions
Bruce from GLOBE, AZ
Stripped screws on a hub drive replacement
Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I already had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well. Read more...
Your Price
$28.24
  In Stock
Bellow To Tub Clamp
★★★★★
★★★★★
(3)
PartSelect Number PS11746259
Manufacturer Part Number WP8540108
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place on the washer frame. The main reason you would want to replace the bellow clamp is if it is rusted or damaged, and it is not holding the bellow in place. To remove the bellow clamp, simply use a screwdriver to pop the bellow clamp out of the groove it rests in. Place the new clamp back into the bellow groove until it snaps into place. This is an OEM part from the manufacturer.
Fixes these symptoms
Installation Instructions
william from wauseon, OH
leaking at door
once i figure out how to take off front panel it went quite smoothly also my wife gave me a hand putting the bellows on,her fingers were smaller so it was alittle easier for her Read more...
Your Price
$6.72
  In Stock
Suspension Spring Retainer
★★★★★
★★★★★
(1)
PartSelect Number PS11749057
Manufacturer Part Number WPW10145155
This is a replacement suspension spring retainer for your washer. The retainer holds the suspension spring in place while the washer is operating. If you notice movement, or an unusual noise or shaking of your washer when it is in use, it could mean that the suspension spring has been disconnected because of a broken or missing spring retainer. You will find the suspension spring retainer at the bottom of the tub assembly. To replace the retainer, use a pair of pliers to disconnect the suspension spring from the chassis mount to relieve the tension. Then, remove the spring from the retaining clip, and remove the retaining clip from the bottom of the washer. Attach the new retaining clip to the bottom of the washer, reattach the spring, and stretch it slightly so it can connect to the chassis. This part is sold individually.
Installation Instructions
RUSSELL from SOUTHOLD, NY
machine was out of balance
Removed the washing machine from the wall and found a broken spring on the floor. Began disassembling the unit before accessing your sight. (Later I viewed your video of the more simple dis assembly).Used your parts breakdown to identify the 6 parts I needed (3 springs and 3 retainers),and ordered them. They arrived on time and as per the video, installed them with ease and reassembled the unit. My wife is very happy. Thank you, Rusty Read more...
Your Price
$7.68
  In Stock
Cover Screw
PartSelect Number PS11740701
Manufacturer Part Number WP308685
Sold individually.
Installation Instructions
Curtis from PALM BAY, FL
Relocating dishwasher into the new kitchen layout
In this case the dishwasher had already been installed for a few years. After removing it, we inspected it and saw it needed a bit of TLC. The transport wheels on the back were missing, making it harder to move around without scratching the tile and some of the original hardware was rusted or broken off. I looked up the parts easily here on PartsSelect using their parts breakdown diagrams and was glad to see what I needed was still available. We had a licensed plumber relocate the hot water line and drain for us to make things a bit easier.
A licensed electrician had also moved the power line over to the new location and left a wire sticking out of the bottom of the wall to hardwire the dishwasher in again. We decided to convert the dishwasher to be able to be plugged into a standard 20amp wall outlet instead. We had already purchased a kit with a nice long cord and strain-relief snap on plastic fitting that snapped onto the metal incoming power box on the bottom front of the dishwasher. Using the supplied wire nuts, etc., we connected the wires and ground wire to the proper wires from the dishwasher and ground lug. We put the dishwasher aside and then went to work on converting the power wire coming out of the bottom of the wall, to a conventional outlet. I am mentioning all this because in our first attempt we unfortunately put the receptacle a bit high off the floor and the new power cord plug end, stuck out and hit the back of the dishwasher so it would not go all the way in and was sticking out from under the counter top. I tried using one of those flat adapter cables, but even that still stuck out to far. So we ended up relocating the outlet box as low as we could on the wall and this allowed the plug to stick out into the opening area at the bottom rear area of the dishwasher so it could now be slid all the way in under the kitchen counter properly. I hope that bit of trial and error will save you some time if you ever decide to go the pluggable route too.
The new installation required the use of the dishwasher side mount brackets, so we had to purchase a replacement set of those, complete with the hardware to screw them down.

This project took a bit longer than planned due to the power plug problem, one which we will remember for any other similar appliance relocation projects, as well as the time to get our new parts in that we had to order, but other than that the rest went smoothly and the dishwasher was relocated successfully. Read more...
Your Price
$20.00
  In Stock
Bellow To Front Panel Clamp
★★★★★
★★★★★
(3)
PartSelect Number PS11773093
Manufacturer Part Number W11032829
The door boot spring clamp or outer bellow clamp on your washer is designed to keep the door boot in place. It is circular in shape, and you will find it wrapped around the bellow. To remove the old clamp, simply open the washer door, and use a screwdriver to pop it out. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
Installation Instructions
Matthew from MENTOR, OH
Torn tub seal causing major water leak.
Removed top of washer. Removed top front panel. Removed old front panel clamp. Removed front door panel. Removed old tub clamp. Then removed torn tub seal. Installed new tub seal. Needed two sets of hands to install new tub seal. Pretty tight installing the new tub seal around drum lip. Might be a good idea to heat up or let your new tub seal soak in water prior to installation. Once tub seal was installed, I installed new tub clamp then re-installed the door switch. After that, I put the front door panel back on. Then tightened down the door switch. Finally, I installed the top front panel and then the top of the washer. Read more...
Your Price
$10.72
  In Stock
Spring Retaining Clip
★★★★★
★★★★★
(3)
PartSelect Number PS11739294
Manufacturer Part Number WP22001650
This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrating and louder than usual during the wash cycle, your spring retaining clip could be faulty or damaged. Check the clip for visible damage, wear, and rust. If you notice any signs of damage, the part should be replaced. Remember to disconnect the power from your washing machine before starting this repair.
Installation Instructions
Ralph from Moreno Valley, CA
unusually loud rumbling in spin mode, no spin out
removed outer enclosure to expose inside workings. removed all retaining springs to tub and transmission housing. Inverted tub to access agitator pulley and belt. Removed pulley and cut belt off.(I knew I was replacing it, anyway.)Had to remove large tub bracket to exchange new pulley for old. Disconnect bleach reservoir filler tubing on tub assembly. Disconnect power connector to drive motor. Removed water pump to access drive pulley where new belt belongs. Aligned belt to pulleys and checked idler pulley tension which was acceptable. Replace helix drive lug against spin/agitator and tightened retaining bolt. Assembled components in reverse order and conducted test run. Success. Smooth running machine and saved about $200 on professional labor costs. I had no repair manual but you should have a personal confidence in general repair work. Something like a history of taking things apart and putting them back together successfully. I had an independent appliance repair guy examine the washer and he said it was too complicated for him. Once I had it apart, it seemed fairly basic. Good luck! Read more...

Related Parts

Back to Top