Tappan Washer Seals and Gaskets
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Tappan Washer Seals and Gaskets
Your Price
$52.67
In Stock
Tappan Washer High Temperature Adhesive
PartSelect Number PS474458
Manufacturer Part Number 5308027429
This high temperature adhesive is used for installing felt and rubber seals on dryers. The tube contains 1 ounce of product. This adhesive is made to withstand extremely hot temperatures. Before applying the adhesive, ensure that the area is completely clean from any debris and is dry. You may wish to use small clamps to hold the material in place while it dries. If the felt has come loose or broken apart, this may cause your dryer to make loud noise, indicating that new felt or rubber needs to be glued into place. Use gloves to apply glue.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Gerald from Alliance, NE
Burned out heater element
1.Remove 2 screws and the air intake grill on the back of the unit. remove the drive belt. 2. Remove 2 screws on rear of top, slide top back and remove. 3. Remove 2 screws about a foot down on the inside on each side of the front cover. Remove four screws that secure the plastic control panel and the front panel that are right behind the control panel on the top. Disconnect the wiring harnesses, cut the nylon wire tie that is closest to the front cover. 3. lay unit on its back and and remove the two screws on the lower edge of the front panel, take your putty knife and slide it in the gap between the front panel and the dryer cabinet and release the two spring clips on both sides. Then you can lift off the front panel and control panel, set it to the side. 4. Remove the screw and the nylon guide from the center of the top front case crossmember. Remove the three screws on the inside rear of the drum, lift out the drum and set aside. 5. The drum pivot just sits in a nylon socket, pop it toward the top of the machine and lift it out, you may want to clean it good and re-lubricate it on reassembly. Disconnect the wires from the heating element and the heat sensor. 6. Set the cabinet upright and remove the four screws on the back side of the rear of the cabinet but not the two that are right in the center, they hold the pivot fixture and don't need to come out. The heater coil pan is now loose and ready for removal. 7. The seal between the filter housing and the blower housing was torn and this is an important part to have right, any air leak here will do the same thing as a dirty lint filter or plugged dryer exhaust and your new heating element will have a short, hot life. I pulled the old one off, scrapped the old glue off, applied the adhesive like the instructions on the tube say and after a few minutes installed the new seal then set the front panel to the side to let the adhesive dry. 8. The reassembly is just the reverse of the disassembly , use a couple nails or awls to help hold the dryer heater pan in place for screw installation and you might want to gentle squeeze the wire connecters if they feel loose, also check for clogged or kinked exhaust and stress the importance of cleaning the lint filter after EVERY load, it is small and all the air that cools the heating element must go through it, if is isn't maintained your new element won't last long. Have fun!
Read more...
Your Price
$31.58
Special Order
Tappan Washer Splash Cover Seal
PartSelect Number PS418992
Manufacturer Part Number 131901400
The tub ring seal or splash cover seal is used for washers. This part seals the tub cover to the outer one and prevents water leakage from around the tub ring. If your seal is damaged and you are experiencing water leakage, it is best to replace this part. Refer to the manual provided by the manufacturer for further installation instructions. Remember to unplug your washer from the power source before starting this installation process.
Fixes these symptoms
- Leaking
- See more...
Your Price
$80.63
Special Order
Your Price
$23.60
Special Order
Your Price
$8.55
Special Order
Your Price
$29.47
Special Order
Your Price
$19.30
Special Order
Your Price
$13.92
Special Order
Your Price
$40.02
Special Order
Tappan Washer Gasket
PartSelect Number PS450509
Manufacturer Part Number 5300183302
This door gasket or seal is used in washers. The rubber gasket creates a protective seal between the washer door and the opening of the washer. The function of this seal is to ensure no water leaks out of the washer when the door is closed for best results during a wash cycle. If your door gasket is ripped or damaged, it is best to replace the gasket to solve this problem. Remember to unplug your appliance from the power source before installing. For installation instructions, refer to the manual provided by the manufacturer.
No Longer Available
Tappan Washer Transmission To Tub Seal Kit
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops. There were a few pieces. Then sealed it back up with the oil that came with the PartSelect Kit and put it back together. Works great now. No more LEAKS! Yippy. Read more...
PartSelect Number PS474640
Manufacturer Part Number 5308950197
This is a transmission to tub seal kit, often referred to as a center tub seal kit, and it is used in washing machines to create a seal between the transmission and the tub. This seal works to prevent leaks from around the basket drive shaft, between the outer tub and the spin basket. We reccomend that you replace the tub seal kit if you are replacing the transmission. The kit includes the instructions you will require for installation. Before you begin the repair on your washer, make sure it is unplugged and the water supply is shut off.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Ron from Williamsburg, MI
Leaking washing machine.
Removing the piece above the tub gasket was very difficult. A lot of hammer and chisel work.15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops. There were a few pieces. Then sealed it back up with the oil that came with the PartSelect Kit and put it back together. Works great now. No more LEAKS! Yippy. Read more...
Related Tappan Washer Parts
- All Tappan Washer parts
- Tappan Washer Brackets and Flanges
- Tappan Washer Caps and Lids
- Tappan Washer Dispensers
- Tappan Washer Hardware
- Tappan Washer Hinges
- Tappan Washer Hoses and Tubes
- Tappan Washer Knobs
- Tappan Washer Latches
- Tappan Washer Panels
- Tappan Washer Springs and Shock Absorbers
- Tappan Washer Switches
- Tappan Washer Wire Plugs and Connectors