Poulan Chainsaw Springs and Shock Absorbers

Poulan Chainsaw Spring Hub Eps

★★★★★

★★★★★

1 Review

Genuine Manufacturer Approved replacement part used on specific Poulan Gas Chainsaws. This item is made out of Metal and it is Sold Individually. This part plays an important role as it provides spring action in the Pull Starter.

Poulan Chainsaw Spring This is an authentic Poulan replacement part manufactured for use with gas powered chainsaws. The ignition switch spring is used to put tension on the throttle control lever. This ignition switch spring is sold as an individual replacement part, please see model diagram for associative parts.

Poulan Chainsaw Spring This replacement part is sourced from the original equipment manufacturer. It is specially designed for use with Poulan, Husqvarna and Jonsered chainsaws. The spring is an important component of the starter mechanism. It applies tension on the pulley allowing it to retract. Unfortunately, over time it may wear out, get damaged or lost eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. This high-quality spring is made of durable metal and is sold individually. You will need a screwdriver to take apart the starter housing in order to perform this repair.

Poulan Chainsaw Spring This is a genuine OEM approved starter spring which is specially designed for use with handheld lawn and garden equipment. It is an identical replacement for a missing or a faulty component that was installed on a new unit. The purpose of this spring is to retract the starter assembly on the engine, so it engages the drive cup on the flywheel to start the engine when pulled. This high-quality spring is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams of your model for the correct location and application of this item.

Poulan Chainsaw Spring This part is an OEM from Husqvarna. The metal spring is made for use with several chainsaws. This item helps to secure the pawl to the flywheel, and is sold individually. A hex key and a pair of pliers are often necessary for the installation.

Poulan Chainsaw Lock Spring This is a genuine manufacturer-sourced replacement part which is specially designed for Husqvarna, Poulan and Jonsered chainsaws. The purpose of this spring is to apply tension on the catch which is sold separately. If the hardware is worn or damaged, this will provide an identical replacement for the original component that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the exact location and the correct repair procedure. Note, this high-quality lock spring is made of durable metal and is sold individually.

Poulan Chainsaw Spring This part is an OEM from Craftsman for use with Chainsaws. The recoil starter hub spring fits between and connects the starter hub and pulley, and applies tension to turn the starter. The most common reasons for replacing the spring start is if the starter rope won't recoil or rewind after pulling or the starter rope won't retract fully back into the housing. This part is sold individually. Here is a list of tools that are needed to replace the recoil starter hub spring a Phillip's screwdriver, Torx drivers, long-nosed pliers, scissors or wire cutters (optional), safety glasses and protective gloves.

Poulan Chainsaw Spring This is a genuine manufacturer-sourced replacement part which is specially designed for Husqvarna, Poulan and Jonsered chainsaws. The purpose of this spring is to apply tension on the connected components. If the hardware is worn or damaged, this will provide an identical replacement for the original component that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the exact location and the correct repair procedure. A screwdriver will be needed to remove and resecure the hardware when replacing this spring.

Poulan Chainsaw Switch, Spring This is an authentic replacement part sourced directly from the manufacturer. The spring switch is found in Husqvarna chainsaws. This part is made of metal, and is placed in the filter housing to provide tension to the switch lever. You will require a screwdriver when replacing this item. The spring switch is available as an individual replacement part.

Poulan Chainsaw Spring This is available as an individual replacement part. The spring attaches to the front handle and is made of a durable material. A screwdriver, a set of pliers, and a socket set may be necessary during the installation of this item. It may become broken and will need to be replaced. This is an OEM part sourced directly from the manufacturer and used in chain saws made by Poulan.