This kit includes the Relay, Overload and cover.
The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed and the Overload provides added protection for the compressor motor because, in addition to protecting against excessive current, it also protects against excessive temperature use.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Fridge too warm | Freezer section too warm
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Barry
October 8, 2019
Stopped cooling, fan is running but does not appear compressor is kicking on.
For model number 6D25DIXHW02
Hello Barry, thank you for writing. This is likely due to either a faulty Overload and Relay Assembly, part number PS11742477, or this Compressor Start Device, part number PS991485 for your model. Good luck with your repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Ken
November 15, 2018
Refrigerator will only kick on if i turn it off and back on again, from the control on the inside. Is this a good part to start with to correct?
For model number ED25UEXHW00
Hello Ken, Thank you for the question. You may have an issue with the Thermostat Assembly, PartSelect Number PS11739232. This thermostat assembly is used in refrigerator units and freezers as a sensor. The thermostat senses the temperature increase in the evaporator during the cycle of defrosting and turns off when ice is melted. If you have any of the following symptoms, replacing your appliance could solve the problem: fridge does not start, is too warm, too cold, runs too long, or will not start. Both the Thermostat and Start Device can be tested with a Multi Meter. Hope this helps, good luck with this repair!
Is this the right start device kit for my refrigerator?
For model number 10659512990
Hello David, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS991485. we hope this helps!
Was this helpful?
Thank you for voting!
Dana
August 9, 2023
I am replacing the "Overload & relay assembly. The wire colors are not the same. It calls out a RED, WHITE, BLUE connection however, I have a BLACK wire instead of BLUE. Do I assume the BLACK goes in place of where the BLUE connects on this new setup?
For model number KSRS25QGBL03
Hello Dana, thank you for reaching out. We have found that the blue wire is connected to the capacitor. If the black wire for your model is connected to the capacitor, you may use it instead of the blue wire. We hope this information is useful!
Was this helpful?
Thank you for voting!
Dana
August 10, 2023
I'm at a point where I replaced 5 parts to finally get both sides operational again. The final part was COMPRESSOR STARER KIT which is completely different than original part. QUESTION: If this is wired incorrectly OR the DEFROST TIMER jumper, would the compressor tank itself become HOT to the touch? I still have the back off and nervous how hot this gets.
For model number KSRS25QGBL03
Hello Dana, thank you for getting in touch. According to our research, if the wires are interchanged, then the compressor will fail to start because the ohmic value of the capacitive reactance conveyed to the start winding will be very high. Hence, the compressor will suffer very low current for its start winding, rendering very poor starting torque. We hope this information helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 7 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Compressor would not operate, very hot.
Removed back cover, noticed the start relay was a Klixon figured it was bad(they don't make a good relay); Checked voltage going to compressor: 115V; Checked ohms: C-S-R 4.3-4.2-4.5; Checked ground: open;
Replaced start relay. Compressor fired right up when plugged in.
Roman from Seymour, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
9 of 11 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
freezer and fridge would not get cold
Take off back lower fridge cover. Removed old startup device. Installed new 2 piece device. Done
Ryan from Hudson, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
7 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cOMPRESSOR WOULD NOT START
Replaced the start Kit , cleaned the condenser coils with a two ft length of 1/2" copper tube taped to the vaccum hose, vaccumed the area at the compressor( this took about 1/2 hour) replaced the cardboard back . (corrected)
The refrigerator works fine. Thanks
Marvin (BUGS) Rentrop
Marvin from New Iberia, LA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
8 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refriderator compressor would not start
Pulled cardboard cover off back of ref to access the compressor compartment. Unplugged appliance, and pull the start device and overload off of compressor. Replaced both parts received from Partselect.com. Refrigerator works great now.
Lisa from Littleton, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
15 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator was clicking from underneath and not cooling or freezing.
First I turned off my refrigerator, called for service, and had the problem diagnosed as a bad start relay. The repairman checked the compressor to see if it too was bad. The compressor was fine so I ordered the part I needed from PartSelect. After receiving the new start relay and overload from PartSelect, I unplugged the refrigerator, pulled it out and removed the screws from the lower back panel with the socket set and screwdriver. I removed the white self contained start relay box from the compressor by gently prying it off with a flat edge screw driver. I carefully disconnected the red and white wires from the broken start relay with pliers and followed the step by step directions that came with the replacement parts (the start relay and overload were separate components, not inside a self contained box like the original part). I proceeded to attach each part to the compressor, reconnect the red and white wires, and attach the new cover. I vacuumed out the area around the compressor and the condensor coils, plugged in the refrigerator, and turned it on. It worked immediately. I screwed the back cover on and pushed it back in place. Within 24 hours the ice maker was nearly full and I saved $225 by doing it myself.
Anne from Middletown, NJ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
28 of 32 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan and Light working but would not cool down inside
This problem first accrued when the unit was under warranty and the repair person told me this would happen again. This technician told me how to troubleshoot the problem and sure enough the Compressor Start Relay was bad again. For starters I moved the refrigerator out from the wall and cabinets. I unplugged the wall cord from the receptacle. I removed the screws, with a ¼ inch spin-tight that held the backing in front of the compressor compartment. I disconnected the two wires then pulled the Start-Dev PS991485 out and it rattled, a good sign the relay was bad. I looked up the Part on the Web Site and ordered the replacement relay, I thought. When the package arrived I found all the parts for the entire Starting and over Temp Protection circuits along with a new plastic cover box. This was a very good experience and I saved maybe $250.00 in repair costs by doing it my self, along with the replacement instruction that came with the parts.
Michael from Yuma, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
13 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator stopped cooling
First I called a repair man to diagnos the problem. He said it was the starter relay and gave me a quote for $300. I looked online and found the part at PartSelect for $55 delivered. I took the back panel off the fridge, unplugged the appliance to stop the flow of electricity (forgot to do that once) and after ensuring the electricity was off, I cut the wiring to the starter relay. After pulling back the wire casing and reconnecting to the new started relay the compressor turned back on and the fridge started cooling again within about an hour. This took roughly 30 minutes to complete and saved me around $250!
Michael from Grand Prairie, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
41 of 45 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Richard D - May 6, 2019
Verified Purchase
Did the trick and then some.
Well my thermostat was going out. This particular fridge has a history of thermostats and relays and starters. Had it fixed under warranty once. Kenmore twice. They have a great program for those not confident in diy. Didn't buy it from them either. Anyhow replaced thermostat and defrost timer about 5 to six years ago myself with parts and instructions from Parts Select. This time around I knew what was up and were to order parts. Ordered a thermostat and defrost timer. There both close together so I do them both. Did the thermostat first, fired it up and on she came. Then did the timer. I want to add for anyone doing the defrost timer. When you first turn your unit back on it may take up to ten minutes or so to kick on. Reason being I believe is your timer might be in a defrost cycle. I had that happen both times to me. Another issue I had was when the fridge kicked on it was really dimming the lights including messing with my window AC units. Also you could hear the starter clicking quite hard. Went ahead and ordered a starter and relay. Didn't have to much in guidance other then find the compressor. There attached to it. Pulled the bottom back panel and there sat the compressor on the left side. Since it had been changed before the spade connections were fine. The starter and relay slide onto prongs coming out of the compressor body. Complete time involved maybe fifteen minutes. Though I did spend another thirty minutes with the vacuum cleaner on the cooling coils. Parts Select sent me 2 relays and starters. Depending on your fridges cubic feet will determine which ones to use. Now the only thing I hear from my 19 year old fridge is the hum of the cooling fan and compressor. Quiet as a mouse and no more blackouts when it kicks on. She still will hit 10 below in the freezer and keeps my fridge between 33 and 32 degrees. I keep it that cold because here in the south especially on weekends the fridge gets opened and closed a bunch. Even after an active day she still stays below 40.Thank you Parts Select.
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS991485
Manufacturer Part Number: 8201799
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
Same-day Shipping
Ships from USA
1 Year Warranty
365 Day Returns
