2003650-1-M-Whirlpool-12002211-Clutch and Pulley Assembly
Part Location Diagram of 12002211 Whirlpool Clutch and Pulley Assembly
See part 5 in the diagram
( Grid squares measure 1x1 inch )
2003650-1-S-Whirlpool-12002211-Clutch and Pulley Assembly 2003650-2-S-Whirlpool-12002211-Clutch and Pulley Assembly 2003650-3-S-Whirlpool-12002211-Clutch and Pulley Assembly Part Location Diagram of 12002211 Whirlpool Clutch and Pulley Assembly
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Clutch and Pulley Assembly 12002211

Rated by 3 customers 

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 257.41
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS2003650
Manufacturer Part Number 12002211
Manufactured by Whirlpool
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Maytag.
Part# 12002211 replaces these:
AP4009131, 1032791, 12002211, 12002211, 25001200
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.8 / 5.0, 3 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer won't spin - everything else works
Ran diagnostic check that machine will automatically perform if you push the right combination of buttons (see instructions tucked behind back panel of control panel) All Systems checked out OK. Took flat screwdriver pushed in the two tabs under the top where it meets the front. Top is hinged so just opened it up. Remove two screws holding front cover. Lift cover forward and up to remove. Loosen 1/2" nut that holds drive motor in position. Push motor toward tub, roll off belt. Take socket and remove bolt in center of clutch. Clutch pulls straight down to remove. Install new clutch. Use screwdriver to leverage tension on motor to put tension on belt, tighten bolt to hold motor in position with correct tension on belt. Install front cover. Lower lid. All done.
Read less
  • Eric from Winder, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
10 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Belt Broke
Luckily, I found someone else with the same story, and read that you need the clutch assembly and the belt at the same time. One night when we started the washer, it made a metal seizing type squeal. There was smoke everywhere. After opening the washer, the belt burned through but the clutch had also seized which was the cause. Replaced both. Needle bearings were totally rusted. Must be leaking water somewhere. Just lift top, remove front cover (two screws inside the top). Prop up and secure washer. Loosen the motor bolt. Through the hole in bottom, fit socket to hex bolt on clutch. Our belt was already off as it broke in half. Remove clutch, slip new one on and make sure it goes all the way back on transmission. Place the one bolt back on. Two people are helpful here! Place new belt on grooves of motor pully (while person 2 holds the agitators still) and then work belt down and around clutch. Ours was a tight fit! Have a person pull back on motor as you tighten the one bolt you loosened. There is an in/lb rating on clutch bolt. Put washer back down and panel back together. Pretty easy repair to save tons on a new washer.
Ordered parts on a Friday at 3:05 pm, and they were delivered the next day! Excellent service!!! This saved our day!
Read less
Other Parts Used:
Stretch Belt Clutch and Pulley Assembly
  • Nicole from Ottsville, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
19 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
machine would not function on "spin" cycle
Maytag repairperson suggested machine was not worth repairing. However, it was only 5 years old and still looked like new. I appreciate availability of this multi-function pulley ass'y from your firm. I removed the tub/spinner unit from machine. This made replacement much easier. Pulley was a little tricky to install. All the wiring is connected in harnesses and simple to re-install. The machine works great now and we are thrilled with it. Thanks again!
Read less
  • Dennis from Fairfax, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
10 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Adam
August 15, 2017
Is there a pulley that i can pull to put a new belt on?
For model number Fav9800wwa
PartSelect logo
Hello Adam, thank you for contacting us. To put that belt on you would loosen the bolt on the motor that adjusts the belt tension, put new belt on motor first and then slide over big pulley. It may be a tight fit. Hope this helps!

Was this helpful?
Thank you for voting!
  • 1
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2003650
Manufacturer Part Number: 12002211
Brand
Model Number
Description
Maytag
FAV6800AWQ
Washer - Residential
Maytag
FAV6800AWW
Washer - Residential
Maytag
FAV9800AWQ
Washer - Residential
Maytag
FAV9800AWW
Washer - Residential
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Clutch and Pulley Assembly
$ 257.41
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.