Front Glide Kit 12002126 | Official Whirlpool Part | Fast Shipping | PartSelect
Front Glide Kit – Part Number: 12002126
Front Glide Kit – Part Number: 12002126 Front Glide Kit – Part Number: 12002126 Front Glide Kit – Part Number: 12002126 https://partselectcom.azureedge.net/Schematics/Maytag/43269.gif

Front Glide Kit

Product Description

Front Glide Kit Specifications

This kit includes 2 glides (left and right), 2 pads with adhesive backing and 1 support brace.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Noisy, Will not tumble.

This part works with the following products:

Dryer.

This part works with the following brands:

Norge, Magic Chef, Maytag, Admiral, Crosley, Jenn-Air, Hoover, Amana.

Part # 12002126 replaces these:

1023864, 12002126, 53-0311N, 53-0665, AP4008680, LA1007, LA-1007.
Part Videos

Replacing your Norge Dryer Front Glide Kit

Customer Repair Stories
Average Repair Rating: 2.7 / 5.0, 4 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Thomas from Oneonta, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
LA-1008, 12002126, WPA3167501, 341241
Dryer made a loud noise and vibrated badly
First I made sure the unit was unplugged. I popped the top of the unit with a slotted screw driver, lifted the top up and rested it against the wall behind the dryer. I removed the two screws - one on each side in front on top of the dryer cabinet. Then I tipped back the front panel of the dryer slightly with the door of the dryer closed. I unclipped the door switch with a slotted screw driver and then lifted the entire front panel including the door off of the the two floor clips on bottom. I set the front panel aside. Next I lifted the large drum slightly to dislodge the rollers in back and slid the drum back slowly while sliding the thin belt back on the drum until the drum was out of the unit and the belt was detached and loose. Then I cleaned the unit thoroughly, vacuumed all lint and dirt and wiped down the outside of the large drum with mineral spirits to make sure it was totally clean and smooth. Then I removed the two rollers and the roller shafts at the back of the unit following the directions enclosed. My slip-ring pliers came in handy to remove the retaining rings on the roller shafts. I replaced the rollers and roller shafts and the supplied washers and spacers as per the instructions. I sprayed a little WD-40 on the surface of the rollers and it stopped all squeaking and vibration of the drum. Next I replaced the front drum pads and runners as per the instructions. I then slid the drum back in place taking care to slide the new belt back around the drum in the same position as the old belt. Now came the difficult part - laying on the floor and reaching under the drum I positioned the belt around the motor shaft and tension pulley. This must be done by "feel" and must be done correctly!! Follow the instructions on the positioning of the belt very carefully and make sure it is in the correct position on the drum, motor shaft, and tension pulley! Next, get up and rock the drum up and down slightly to make sure it has engaged the two rear rollers properly. Rotate the drum manually one or two turns to make sure the belt is in the correct position. Then replace the front door panel by dropping it onto the two clips at the base of the unit and taking care to replace the door switch in reverse order of taking it out. Then replace the two screws at the top front on each side of the unit to secure the front panel. Lower the top of the unit back in place, plug in the dryer, turn it on and enjoy the lack of noise you have created.
48 of 56 people found this instruction helpful.
Was this instruction helpful to you?
JEan from Cypress, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
Parts Used:
WP31001747, 12002126
Loud screeching metal to metal sound. The roller and "axle" were worn out.
First I disconnected the power cord. Next the top of the dryer was easily popped upen with a screw driver by inserting it between the top panel and the front door panel. I removed the two sheet metal screws that held the door panel on the upper right and left sides. The door panel was easily lifted up and out and set it to the side (the door switch can stay connected, the wire is long enough). d I pulled the drum out from off of the rollers that hold the drum in place. No need to remove the belt, it stays in place. I reached through the drum and removed the two hex-head screws that held the roller in place ( I only replaced the left one) and added the new one. I pushed the drum back in place over the rollers (it snaps in place). I propped the drum up with a short screw driver to raise it off of the right and left drum glides (on the bottom). I replaced the felt pads and the plastic glides and set the drum back in place. I also replaced the felt ring (seal) that circles the door opening that the drum also glides on. I glued it in place in spots (with gasket glue). It folds back over itself and forms a double thick pad. You will see what I mean when you see how the old one looks. I replaced the front door panel and snapped the top panel back in place. I let the dryer set over night so the glue would set up. I turned it on the next morning and it is as quiet now as when it was new. Oh ...Jay (the husband) did the work not Jean the wife (her dryer, her credit card)
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Dale from YONKERS, NY
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench set
Parts Used:
LA-1008, 12002126, 341241
Dryer was squealing while spinning
I followed the directions from a post on parts select that somebody had previously written and my repair worked out perfectly. I removed the top / lid of the dryer by placing a flat head screwdriver underneath both top front corners which was relatively simple. I then removed the entire front door of the dryer by disconnecting the electric wires for the door which again was a very simple procedure. The tumbler was now exposed at which time I removed the belt (I took a picture of the belt setup for later reassembly) and lifted the tumbler off giving myself easy access to the rear drum rollers and front drum pads. I was able to see that the wheels were worn and definitely the cause of the squealing. I changed out the wheels with replacement wheels which was self explanatory. The front pads were in good shape but I figured that at this point it would serve me well to replace them also which I did. I then reset the new belt (another part that I opted to change while I had the opportunity) on the tumbler with the picture in hand and had no problem. This step did require two people but still not a difficult step. I then put the door and lid back together and now had myself an extremely quiet dryer and a piece of mind that new parts were installed. All in all pretty easy repair.
8 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Gary from Park Hills, MO
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Parts Used:
12002126
Originally Noisey While Running
Unplugged electric, turned off gas valve. Opened top using a putty knife, laid it gently back against the wall for support. Removed 2 screws holding front on-leaned front out about 3-4 inches- while holding front with my knees I disconnected door switch wires.-then removed front panel. Followed instructions on maintenance sheet glued on underside of dryer top (Lucky it was there). Took tension off drive belt. Removed belt and drum following instructions on lid sheet. Removed old slides (worn out) Installed new pads & slides. Vacuumed out all lint/dust/dirt I could reach, Cheked rear drum rollers. Reinstalled everything that I had removed. It took extra time to do everything because dryer was in tight space, little working space. Turned gas on, plugged in electric cord. Worked great now.
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
1 Review
3
out of 5
Filter By Rating:
  • 5 Stars
    0
  • 4 Stars
    0
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS2003584
Manufacturer Part Number: 12002126
Brand
Model Number
Description
Norge
7002A
Dryer - DRYER
Norge
7215A
Dryer - ELECTRIC DRYER
Norge
7215A REV A
Dryer - Norge Dryer Model 7215A REV A (7215AREVA) Parts
Norge
7215A REV B
Dryer - Norge Dryer Model 7215A REV B (7215AREVB) Parts
Norge
7215A REV C
Dryer - Norge Dryer Model 7215A REV C (7215AREVC) Parts
Norge
7215A REV D
Dryer - Norge Dryer Model 7215A REV D (7215AREVD) Parts
Norge
7215A REV E
Dryer - Norge Dryer Model 7215A REV E (7215AREVE) Parts
Norge
7215A REV F
Dryer - Norge Dryer Model 7215A REV F (7215AREVF) Parts
Norge
7215A REV G
Dryer - Norge Dryer Model 7215A REV G (7215AREVG) Parts
Norge
7216A
Dryer - ELECTRIC DRYER
Norge
7216A REV A
Dryer - Norge Dryer Model 7216A REV A (7216AREVA) Parts
Norge
7216A REV B
Dryer - Norge Dryer Model 7216A REV B (7216AREVB) Parts
Norge
7216A REV D
Dryer - Norge Dryer Model 7216A REV D (7216AREVD) Parts
Norge
7216A REV E
Dryer - Norge Dryer Model 7216A REV E (7216AREVE) Parts
Norge
7216A REV F
Dryer - Norge Dryer Model 7216A REV F (7216AREVF) Parts
Norge
7375A
Dryer - ELECTRIC DRYER
Norge
7375A REV A
Dryer - Norge Dryer Model 7375A REV A (7375AREVA) Parts
Norge
7375A REV B
Dryer - Norge Dryer Model 7375A REV B (7375AREVB) Parts
Norge
7375A REV C
Dryer - Norge Dryer Model 7375A REV C (7375AREVC) Parts
Norge
7375A REV D
Dryer - Norge Dryer Model 7375A REV D (7375AREVD) Parts
Norge
7375A REV E
Dryer - Norge Dryer Model 7375A REV E (7375AREVE) Parts
Norge
7375A REV F
Dryer - Norge Dryer Model 7375A REV F (7375AREVF) Parts
Norge
7433A
Dryer - ELECTRIC DRYER
Norge
7433A REV A
Dryer - Norge Dryer Model 7433A REV A (7433AREVA) Parts
Norge
7435A
Dryer - ELECTRIC DRYER
Norge
7435A REV A
Dryer - Norge Dryer Model 7435A REV A (7435AREVA) Parts
Norge
7435A REV B
Dryer - Norge Dryer Model 7435A REV B (7435AREVB) Parts
Norge
7435A REV C
Dryer - Norge Dryer Model 7435A REV C (7435AREVC) Parts
Norge
7435A REV D
Dryer - Norge Dryer Model 7435A REV D (7435AREVD) Parts
Norge
7435A REV F
Dryer - Norge Dryer Model 7435A REV F (7435AREVF) Parts