Dishwasher Heating Element WPW10082892

Hello Dean, Thank you for the question. The element should read between 10-20 ohms. Hope this helps!

Hi Kurt, Thank you for your question. Usually when something like this happens with your bake element it means that something has dripped on the element. Which may be the reason that the part has stopped working. It sounds like you will have to replace your bake element, but you can test it with a multi meter to double check if it is working or not. I hope that helps. Good luck with your repair.

Hello Jason, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is PartSelect Number: PS11748194. The rubber washers, Part Number: PS11743934 and nuts, Part Number: PS11745448 are sold separately. Hope this helps!

Hello Joseph, thank you for asking. According to our research, this heating element is part number PS11748194. The nut that fits with this element is part number PS11755402. This part comes with 1 nut, you would have to order two of them. We look forward to hearing from you if you need assistance with placing an order through our 7-days-a-week customer service. We hope this helps!

Hello Eileen, thank you for your question. There are a few parts that could be the issue. The Heating Element Assembly is one. If lights are flashing on the control panel, the heating element assembly might have burned out. The heating element assembly heats the water up to operating temperature. After a set amount of time if the temperature isn't reached a light on the control panel might start flashing. The heating element assembly can be checked for continuity with an Ohm meter. Drain Pump - If lights are flashing on the control panel, the drain pump might not be working properly. For two-wire drain pump motors check them for continuity using an Ohm meter. If it's defective You'll need to replace it. Drain pumps are not repairable. Touchpad and Control Panel - If the lights are flashing on the display the entire touchpad and control panel assembly might be defective. If the display works but the dishwasher functions are all out of synch, or some of the buttons don't respond properly the entire touchpad and control panel might need to be replaced.I Hope this helps!

Hi Randall, Thank you for your question. There are some parts that you will need to check to see which ones are causing the issue. You will need to check the bi-metal fuse, the door switch, the circulation pump and motor, the high limit thermostat, the door handle, the electronic control board and the heating element. I hope this helps. Thank you and have a great day!

Hello Alan, Thank you for the question. I suggest testing the High Limit Thermostat,PartSelect Number PS11743423. You can also test the element, PartSelect Number PS11748194. When at room temperature, should measure about 6 to 15 ohms. Hope this helps!

Hi Carl, Thank you for your question. If the normal cycle light is flashing, try resetting it by unplugging the dishwasher for 30 seconds. If this does not help, there may be an issue with the door switch. Try opening and then closing the door firmly and selecting a new wash cycle to see if this resolves the issue. If not the door switch will need to be replaced. Try cleaning the control panel to see if this helps. Sometimes a key may be stuck and wiping the control panel with a cloth may help. If the light continues to blink, then you will need to replace the electronic control board. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!

Hello Barb, thank you for reaching out. If the heating element is working fine, we suggest that you check the thermostat, part number PS11743423, and the control board, part number PS11748221, as these could be the culprits of the issue. If you require assistance to place an order, please contact customer service. We hope that helps!

Hi Luanne, Thank you for your question. If the green light is blinking and the dishwasher will not start, the water temperature may be too low. Before starting a cycle on the dishwasher, turn the hot water on in the sink and let it run for a few minutes until it gets good and hot. If the issue persists and the water inside the dishwasher is not hot enough, you will need to check the heating element for continuity with a multimeter on the Rx1 setting. Unplug the dishwasher from the electrical outlet before removing and testing the element. Touch each probe to a terminal. Your reading should be somewhere between zero and infinity, refer to your owner’s manual to determine what reading you should receive for your model. If it is exactly zero or infinity it is defective. If your test produces a reading different from the manufacturer’s recommendation, you will need a replacement heating element. We hope this helps!