Maytag/Maytag_Thumb/OJASJLMY.gif
See part 9 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Washer Control Timer

★★★★★
★★★★★
4 Reviews
$146.12   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11742046
Manufacturer Part Number WP3951702
Manufactured by Whirlpool
Product Description

Washer Control Timer Specifications

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.(60 Hz.)

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Timer will not advance | Will not drain
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Crosley, Maytag, Amana.
Part# WP3951702 replaces these:
AP6008905, 3951702
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

7 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Basem
    August 24, 2017
    Hi. I need a replacement part (timer), for my washing machine (220v)
    For model number CAWS953RQ1
    Hello Basem, thank you for contacting us. This would be the correct timer for your model. Good luck with the repair!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Gerry
    February 11, 2020
    Washer fills, and agitates but will not spin or empty. The switch makes a heavy buzzing noise. Could it have a bad switch?
    For model number LSQ8511KQo
    Hi Gerry, Thank you for your question. If the washer is not draining or spinning, the issue is likely the lid switch and you will need to replace it. You will need to test the switch with a multi-meter to verify if it is working correctly. Set your multi-meter to the Rx1 setting, touch the probes to the terminals, and press and hold the switch button down. The multi-meter should show a reading of zero or nearly zero. If your test produces different results, you will need a replacement lid switch. We hope this helps. Thank you and have a great day.

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Bill
    October 14, 2017
    Timer stops after agitation cycle. Does that definitely mean the timer is bad, or could it be something else?
    For model number LSB6200KQ0
    Hi Bill, Thank you for your question. If you mean that your appliance will pump water but will not go into the spin cycle, there are a couple of parts that could cause that issue. I would suggest taking a look at your clutch, your direct driver motor coupling, and your driver block for any wear on the parts. Electrically I would first suggest testing your door switch. If the appliance things that the door is open it will not go into the spin cycle. I hope this gives you a starting point. Good luck with your repair.

    Was this helpful?
    Thank you for voting!
    John
    November 4, 2017
    My washer will not fill with water and goes straight to the agitation cycle or when it does fill, it overflows. Will the timer switch solve the problem?
    For model number LSQ9010KT0
    Hi John, Thank you for your question. I would suggest first checking your water pressure switch and your hose. If both of those parts are fine, you should check your water inlet valve next. Those parts would be the most common parts to cause this issue. Good luck with your repair.

    Was this helpful?
    Thank you for voting!
    Jason
    January 12, 2018
    I was looking at the timer control module part and instructions ps11742046 / wp3951702 and was trying to verify this is the correct part. I watched the video , opened the control panel but could not find a black shaft to remove from the timer to get the knob off. Even when the knob is pressed down all the way, i did notice at least the surface part of the knob pops off when pulled, leaving a springy split piece of plastic that latches onto the knob and heads into the module. Not sure if this is a different part, based on that? Thanks, jason
    For model number LSQ9010KQ0
    Hello Jason, Thank you for your inquiry. If it looks like kind of a beige piece of plastic that has two triangles at the end, that is the timer shaft that the knob slides onto. Hope this helps!

    Was this helpful?
    Thank you for voting!
    Brendan
    February 7, 2018
    My washer stops mid cycle and will sit full of water unless i press down on the lid. I changed the lid switch and the timer motor. Still getting the same results. Any suggestions?
    For model number LSQ9544KQ0 Whirlpool Washer -
    Hello Brendan, Thank you for your inquiry. I would check the lid strike to make sure it's not cracked and the wiring going from the switch to the electronic control board. The other parts you can check are the water inlet valve, the direct drive motor coupling, the clutch assembly, the gear case, the drive motor and the electronic control board. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!

    Was this helpful?
    Thank you for voting!
    Steve
    November 6, 2019
    My washer will wash and fill. When it gets to rinse it fills, the timer keeps clicking, and after a while it starts spinning while draining. But it will not agitate on rinse. It goes through a normal spin cycle. This happens in any mode. Does this sound like a timer issue?
    For model number LSB6200KQ0
    Hi Steve, thank you for your question. It could be, however I would also suggest checking the parts of your agitator. It could be that the agitator cogs or other internal parts. They can wear down over time. You may also want to check your motor if all of those parts are fine. I hope that helps. Good luck with your repair.

    Was this helpful?
    Thank you for voting!
      Part Videos

      Replacing your Whirlpool Washer Washer Control Timer

      Customer Repair Stories
       Average Repair Rating: 3.8 / 5.0, 9 reviews. What's this?
        Sort by:
        Sorry, we couldn't find any existing installation instruction that matched.
        washer would'nt cycle
        remove two screws that hold down top piece that holds timer. [screws are at each end] pull the top peice foward[ toward front of washer] just about 1 inch,then flip it up so you can see back of timer,pull out black tab that holds timer knob [with the tweesers],remove knob and dial unplug the wiring remove the screw under timer knob raise clip on the side of timer so it will slide toward left side remove timer. reverse instructions to install. PS VERY IMPORTANT!!!!!MAKE SURE TO UNPLUG WASHER FIRST!!!!!!!!!!!!!!!!!!!
        • michael from deersville, OH
        • Difficulty Level:
          Really Easy
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Screw drivers
        • Parts Used:
          WP3951702
        27 of 28 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Some cycles would not run. Overheating odor.
        Pulled washer out. Removed two top panel screws. Removed panel and removed timer. Reinstalled in reverse order.
        • CLIFFORD from HOT SPRINGS, AR
        • Difficulty Level:
          Really Easy
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Nutdriver, Screw drivers
        • Parts Used:
          WP3951702
        12 of 13 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        bad timer and top half of agitator not working
        Watched how to video and couldnt have been easier. Both repairs made in less than hour. Also doing work myself saved me a "load" of money by not having to call repair man.
        • jason from zanesville, OH
        • Difficulty Level:
          Easy
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Pliers, Screw drivers, Socket set
        • Parts Used:
          80040, WP3951702
        8 of 9 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Two fold: agitator slipping, Washer delays spin cycle untill lid is raised and dropped.
        First repair was easy, remove center bolt, pull up on agitator and replace entire unit as one piece, replace bolt and liquid dispenser.

        Second repair was more difficult in that I could not immediately find the release to remove timer control. After removing 5 screws unnecessaryily and studying unit more closely, tried prying up on little tab that has a "+" symbol on it that locks into a little hole. While holding up on that tab, slide timer unit sideways and unit falls out of washer panel. Simply slide the new unit in and it locks in place.

        Also the directions to remove the knob were convienently printed on the orginal and replacement timer, but an ARROW pointing to the black tab on rear of the timer control would be helpful as I mistook the tab to be on the front side under the knob from studing the replacement and tried to pull the smaller inter knob off in order to push it in to release the larger outside knob portion in order to disconnect the timer. No harm done, eventually figured it out, but it still didn't fix the problem. As the washer will EVENTUALLY go in the spin cycle without picking up and dropping the lid, I'm assuming the lid switch is defective, although it appears to work otherwise. Any other possible soulutions appreciated.
        • Linda from Enola, PA
        • Difficulty Level:
          A Bit Difficult
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Socket set
        • Parts Used:
          WP3951744, WP3951702
        8 of 11 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        would not spin or wash
        First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
        • Joseph from Park Hill, OK
        • Difficulty Level:
          Easy
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Nutdriver, Pliers, Socket set
        • Parts Used:
          WP3951702
        7 of 12 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Washer Would Not Agitate On Normal Setting But Worked Fine In Other Settings
        Removed control knobs from front (small ones pull off leave large one in place for now). Remove 2 screws from back and remove 2 nutdrivers screws from back and lift top up. Remove large knob instructions on timer. Remove wiring plug and 2 screws from under the knob. Put new timer in place attach with screws. Plug wiring into timer. Re install the back with 4 screws. Once top in place re install the small knobs. Job complete.
        • MICHAEL from SALISBURY, MD
        • Difficulty Level:
          Really Easy
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Nutdriver, Screw drivers
        • Parts Used:
          WP3951702
        6 of 7 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        would not do a thing, timer made sad noise
        I took the top off with the two screws that were hidden in the back, then it was a breeze, replaced the timer and it still did not operate, she had also broke the lid switch trying to made it work. I was inpressed that she wanted to do the wash so bad. thanks for having the parts in stock.......
        • dan from osage beach, MO
        • Difficulty Level:
          Easy
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Nutdriver, Screw drivers
        • Parts Used:
          WP3951702
        4 of 5 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Washer would not agitate after filling the tank, had a humming sound, and a smell like burnt electronic component.
        First, i checked to see if the motor was bad. I moved the selector switch to spin, to see if it would drain the tub. After a couple minutes, it not only drained, but the motor started the spin cycle....motor not bad. Tilted the washer forward and saw 2 screws to remove the control cover. Instructions to remove the timer was on the back. Smelled the timer and same odor. Ordered new part and reverse assembly. Set to light wash load and let it cycle. OK !!
        • Clifford from Defiance, OH
        • Difficulty Level:
          Really Easy
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Pliers, Screw drivers
        • Parts Used:
          WP3951702
        3 of 5 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Timer had issues and stopped at a certain point and would not advance/continue.
        Remove and replace the timer. A little bit of patients helps to figure out removing the top panel, after that it is a relatively simple replacement.
        • Don from ROHNERT PARK, CA
        • Difficulty Level:
          Really Easy
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Nutdriver, Screw drivers
        • Parts Used:
          WP3951702
        1 person found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
          Customer Reviews
          Average Rating:
          ★★★★★
          ★★★★★
          4 Reviews
          5.0
          Filter By Rating:
          • 5 Stars
            4
          • 4 Stars
            0
          • 3 Stars
            0
          • 2 Stars
            0
          • 1 Star
            0
            Sort by:
            Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
              Model Cross Reference
              This part works with the following models:
              PartSelect Number: PS11742046
              Manufacturer Part Number: WP3951702
              Brand
              Model Number
              Description
              Whirlpool
              7LSC8244HQ0
              Washer
              Whirlpool
              7LSC8244HZ0
              Washer
              Whirlpool
              7LSC9245HQ0
              Washer
              Whirlpool
              7LSR8244HQ0
              Washer
              Whirlpool
              7LSR9245HZ0
              Washer
              Whirlpool
              7MLSC9000PW0
              Washer - Residential
              Whirlpool
              7MLSC9000PW1
              Washer - Residential
              Whirlpool
              7MLSC9545JQ2
              Washer - WASHER
              Whirlpool
              7MLSC9545JQ4
              Washer - Residential
              Whirlpool
              7MLSC9545JQ5
              Washer - Residential
              Whirlpool
              7MLSC9545JQ6
              Washer - Residential
              Whirlpool
              7MLSC9900PW0
              Washer - Residential
              Whirlpool
              7MLSC9900PW1
              Washer - Residential
              Whirlpool
              7MLSQ8545PG1
              Washer - Residential
              Whirlpool
              7MLSQ8545PQ0
              Washer - Residential
              Whirlpool
              7MLSQ8545PQ1
              Washer - Residential
              Whirlpool
              7MLSQ8545PT0
              Washer - Residential
              Whirlpool
              7MLSQ8545PT1
              Washer - Residential
              Whirlpool
              7MLSQ8545PW0
              Washer - Residential
              Whirlpool
              7MLSQ8545PW1
              Washer - Residential
              Whirlpool
              7MLSQ9549PQ0
              Washer - Residential
              Whirlpool
              7MLSQ9549PQ1
              Washer - Residential
              Whirlpool
              7MLSR8544JQ7
              Washer - Residential
              Whirlpool
              7MLSR8544JT0
              Washer - Residential
              Whirlpool
              7MLSR8544JT4
              Washer
              Whirlpool
              7MLSR8544JT5
              Washer - Residential
              Whirlpool
              7MLSR8544JT6
              Washer - Residential
              Maytag
              7MMMS0100VW0
              Washer - Residential
              Maytag
              7MMPH0080VM0
              Washer - Residential
              Maytag
              7MMPM0060VM0
              Washer - Residential

              Get in touch, we're here to help!

              Open until 10PM EST

              Contact Customer Service