V-Style Drive Belt (32.5 inches long) WP28808 | Official Whirlpool Part | Fast Shipping | PartSelect
V-Style Drive Belt (32.5 inches long) – Part Number: WP28808
V-Style Drive Belt (32.5 inches long) – Part Number: WP28808 V-Style Drive Belt (32.5 inches long) – Part Number: WP28808 V-Style Drive Belt (32.5 inches long) – Part Number: WP28808 V-Style Drive Belt (32.5 inches long) – Part Number: WP28808 https://partselectcom.azureedge.net/Schematics/Maytag/17847.gif

V-Style Drive Belt (32.5 inches long)

Product Description

V-Style Drive Belt (32.5 inches long) Specifications

This v-style drive belt is thirty-two and a half inches long and half of an inch wide.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Noisy | Will not agitate | Leaking | Pumps but will not spin

This part works with the following products:

Washer, Washer Dryer Combo.

This part works with the following brands:

Amana, Crosley, Speed Queen, Maytag, Magic Chef.

Part # WP28808 replaces these:

28808, R0606539.
Questions and Answers
Be the first to ask our experts a question about this part!
Customer Repair Stories
Average Repair Rating: 3.6 / 5.0, 13 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
John from Milton, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WP28808
Frayed V-belt
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, remove 4 mounting bracket screws that secure the motor and pump assembly. Pull back the tension/idler pulley to loosen belt off the main pulley to the washer drum. Tilt and pull out motor/pump assembly. Underneath the pump, use star-bit to remove the pump from motor assembly to remove the belt. Install new belt on motor pulley (Good time to check for debris or anything restricing free movement of pump) and re-install pump. Install the motor/pump assembly and loosely secure the motor/pump assembly. Place the belt onto the motor pulley and pull back the tensioner/idler pulley to allow slack of belt to be placed on washer drum pulley. Put the belt on the lip of the drum pulley and rotate while pulling back the tensioner/idler pulley until the belt is seated on the groove of the drum pulley. Tighten the motor/pump assembley. Re-attach the 2 hoses and tighten down the clamps. Re-connect the electrical connector to the motor...Don't forget to plug in the washer and secure the front panel...Piece 'O cake, you're done! About 15 minutes to do the job. Much like changing a belt on most vehicles.
54 of 61 people found this instruction helpful.
Was this instruction helpful to you?
Charles from Cliff, NM
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench set
Parts Used:
WP28808, 27001233
Water was leaking from the bottom of the machine, tub wasn't filling
This was on a machine at a friends house I was watching while he was away. I spent more time looking for tools than the actual repair. Once I figured out how to get the front panel off (two bolts at the bottom of the front panel) the problem was easy to diagnose, water was running out of the pump seal. When the parts arrived the repair took about 15 minutes. Shut offpower. remove the 2 bolts holding the plastic cover over the wiring harness, remove the cover and unplug the wiring harness. Losen up the clamps on the hoses to the pump. Place a towel or drip pan under the pump when you pull the hoses lose. Next remove the four bolts at the base of the motor/pump mount. Slip the belt below the bottom of the tub pulley and remove the motor/pump assembly. Remember the position of the idler/tensioner pulley in relation to the belt. Pull the pump off the shaft by removing the three torx head screws holding the pump to the bracket and replace. Reverse the procedure to reassemble. It is a good idea to replace the belt when replacing the pump, the one in the machine I was repairing was cracked and dry, on its last lap. Good luck.
14 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Tim from Cumming, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Parts Used:
WP28808, 28800
Machine stopped in spin cycle and smell of burnt plastic.
Removed pump/motor assembly. Had a difficult time removing pump from motor. Was not aware that the shaft was not connected some way! After looking over the internet for help....I finally realized that the shaft was siezed in the pump. After much persuasion on my part....it broke loose... I did use some WD-40....but don't know if it....or my prying between the pulley and the pump finally did the trick. Found that the idler pulley was seized. When I replaces both belt and pulley... It worked fine...
14 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Peter from Westport, MA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WP28808, 27001233
Leaking pump, torn belt, washer 24 yrs old
Please read the comments from other people before you start the repair. The hints are great, and save you time.
Removing the old pump from the shaft with two screwdrivers
by gently prying it off the shaft was the best idea. Once the pump is removed from the motor, it is a snap to replace the belt, and tension pulley if necessary.
The metal surfaces are sharp inside the machine, and I suggest placing a good light inside the machine so that you can see where the belt goes. Follow Joseph's instructions from Goldsboro NC to a tee, and your repair will be a great experience.
Peter
Westport, Ma
10 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Eric from Akron, OH
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
WP28808
Wouldn't agitate or spin.
This was my fist time attempting to fix a washer. I had to guess on the length of the belt since the model number on the machine had worn off and the belt had snapped in a way that made determining the length difficult. At first, I ordered a belt that was too small. I realized this after I was unable to remount the motor stand onto the bottom of the machine. This model had the motor assembly right in front of the unit. It was easily accessed after removing the panel on the front of the machine. It was easy to remove the 4 screws (they were all visible) on the motor stand. After that I was able to disconnect the pump belt. This machine has seperate belts for agitation and the pump. The pump belt must be removed in order to install the agitator belt because they both are driven by the same shaft and the pump belt is positioned on the bottom. There is also a tension wheel for the agitator belt which might be easily overlooked. Make sure to install the agitator belt so that the tension wheel is on the outside of the belt's path. The whole job is fairly easy if you have the right part to begin with. If you have to force the belt onto the wheels, then you probably have a belt that is too small.
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Stanley from Lebanon, IN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WP28808, WP27155
Worn belt
Released idler pulley and replaced belt
8 of 15 people found this instruction helpful.
Was this instruction helpful to you?
C from Palatine, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Parts Used:
WP28808
none
took the drive belt to the pump off then put the belt for the drum on .then put the belt for pump back on. basickly this unit is one of the easist to work on
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
William from Bristol, CT
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Parts Used:
27001233, WP28808
Pump was leaking
Unplugged machine from wall, disconnected supply hosesand removed drain pipe from drain. Removed pump/motor assy located in the front of the machine. Replaced pump and belt. Be carefule how you route the belt. Upon inspection before powering up I noticed I ran the belt wrong and it was rubbing on one of the pumps plastice screw housing. Had to disassemble, re-route belt and re-assemble. Powered machine up and it worked great.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Dennis from Pensacola, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Parts Used:
WP28808, 27001233
Water pump leaking, belt 20 years old
Removed motor apparatus with socket, took off water pump with star srewdriver . Installed new pump. Replaced belt. Schematic diagram big help...
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
matt from bruce crossing, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
WP28808, 28800, 27001233
water leaking not agitating and shaking in spin cycle
remove front panel. unplug motor. remove 4 screws and take motor,pump,idler and belt assembly out. remove pump from bottom of motor. 3 screws held pump and drove off with hammer. replace idler and install belt before new pump. install pump. reinstall assembly. works good now.
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
3 Reviews
4.7
out of 5
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11740616
Manufacturer Part Number: WP28808
Brand
Model Number
Description
Amana
AA3110
Washer - Top Loading
Amana
AA3111
Washer - Top Loading
Amana
AA3210
Washer - Top Loading
Amana
AA3410
Washer - Top Loading
Amana
AA4110
Washer - Top Loading
Amana
AA4111
Washer - Top Loading
Amana
AA4210
Washer - Top Loading
Amana
AA4211
Washer - Top Loading
Amana
AA4410
Washer - Top Loading
Amana
AA4411
Washer - Top Loading
Amana
AA5121
Washer - Top Loading
Amana
AA5220
Washer - Top Loading
Amana
AA5221
Washer - Top Loading
Amana
AA5222
Washer - Top Loading
Amana
AA5420
Washer - Top Loading
Amana
AA5421
Washer - Top Loading
Amana
AA6121
Washer - Top Loading
Amana
AA6221
Washer - Top Loading
Amana
AA6421
Washer - Top Loading
Amana
AA7131
Washer - Top Loading
Amana
AA7231
Washer - Top Loading
Amana
AA8431
Washer - Top Loading
Amana
AA9131
Washer - Top Loading
Amana
AA9231
Washer - Top Loading
Amana
AA9431
Washer - Top Loading
Amana
AWE852
Washer - Top Loading
Amana
AWE931
Washer - Top Loading
Amana
AWE951
Washer - Top Loading
Amana
AWM190W
Washer - Top Loading
Amana
AWM190W2
Washer - Residential, Automatic