ZISW36DCB General Electric Refrigerator - Instructions

Since I really needed to replace the deteriating auger I used the original ice bucket and transferred the new auger assembly into the old ice bucket. Looked complicated at first, but make it work and my refrigerator is now making nice clean ice. It would have taken a lot longer if I sent the new bigger ice bucket back and it was my fault. With the videos and pictures on line made the replacement of the auger & ice bucket easy. Thanks Bill

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

changed both inlet valves, did diognostic on old ice maker. replaced with a new one from partselect.I have a cupple notes of interest. One, do not count on the instructions sent with part , I't took me a while to figure out that they do not necesarly apply to my unit. no diognostic light on new unit. and you don't have to follow the same procedures. I finished the project but the added help hindered me more than helped.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

Opened, discovered not flapper but more complicated

Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

Removed 4 screws holding back, removed water connection, removed screw holding bracket to frame disconnected electrical removed lines connected to valve assembly and installed valve assembly in reverse order.,

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

Watched you tube video a few times,very helpful.A word of advice take a good,look at the part you are replacing before ordering,dont go by model #,I ordered according to the model and that part did not fit. You also need a 5/16 snap on union for one of the cracked lines,ordered it from GE worked fine.

1) Shut off water supply
2) Pull out Refrigerator
3) Unplug
4) Unscrew back panel
5) Remove main water supply line
6) Remove bracket
7) Cut supply hoses 1 at a time and insert in new assembly in correponding openings
8) Reverse steps and enjoy

Notes: Judging by the new part's look, I suspect this repair will be needed again in about the same amount of time (5 years). The incoming pressure (I live in NYC) is probably too much for the way the part is built. Fortunately, now I know where to look , what to order and where to get it (great service, partselect.com!) it's no more then a 15 minute job.

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!

Turned off the water and unplugged the frig. Removed the assembly (the hard part as it was corrodided) by removing 4 screws and slipping the electrical connections off. The water lines slipped off easilyThe instructions were good and the part fit easily. Then reversed the process by connecting the electrical and water.
I ordered the part via internet on Wed. evening and received it on Friday. Excellant service!

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.