Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
digital readout was faded and unreadible
Removed three screws from top of display/control panel. Open upper oven door and remove 4 screws from botton of display/control panel. Pulled panel off and rested it face down on top rack of I pulled out of upper oven. removed 2 wiring harnesses and ribbon wiring form clock assembly. Remove four screws with nutdriver and remove clock assembly. Replace clock assembly and reasseble in reverse order from above.
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
We had a wood tray in the oven (yes i know) and it is a two stacked oven and turned the wrong oven to broil. The fire was put out quickly but the Latch door switch and assembly was damaged. The 3D breakout of the appliance made it a jiffy to select the correct part numbers. Shipping is very good from Parts Select. The Front assembly for the lower oven comes out with 6 screws. Disconnect the Door Switch Connector push it out and replace that. The Latch Assembly requires a small wrench. It is a bad design but patience will get you there. Once the assembly is out disconnect electrical connectors. Don't worry each connector is unique I advice do it one for one. Overall you need a skill of three stars out of five to complete this task
Clock time display was very faded, barely visible and when the oven temperature and/or timer were activated, the entire display was not visible. User had to guess the temperature and time.
First we disconnected power to the oven. Then we removed the two screws that attached the oven control panel cover to the body of the oven. Next we removed the screws that secured the faulty clock assembly to the control panel. Then we un-installed the three cable/connectors. The two wire cable/connectors were simple pull-outs. But with no instructions in either the Users Manual or shipped with the replacement part, we had no idea how to un-install the ribbon cable. Fifteen minutes later, much trial and error, and simple blind luck, we finally realized that we simply had to lift up the connector ears and the ribbon cable would disengage. Then it was a simple matter of seating the replacement assembly, installing the two screws, re-installing the three cables, reseating the control panel cover and re-installing the cover screws. Once power was restored to the oven, the clock was reset. We tested the oven temperature and the timer. All was well once again. Question: Would you like us to return the faulty Jenn-Air part for trouble-shooting? Recommendation for the future: Send some simple installation instructions. We both have computer manufacturing asembling experience but never worked with a ribbon cable connector like this one. That connector was a major stumbling block for us. A simple changeout turned into a 30+ battle. But, I would like to thank you for the quick shipment of this part. It was ordered on a Monday and received in Wednesday's mail. That so FAST! and very much appreciated. Your website is now in my Favorites and in my email address book. Thank you once again for all your help. Sharon Hall 133 Lake View Drive Spicewood, TX 78669 830 693-4513 thumper@tstar.net
The bake element got so hot it caught fire! The electrical type
We cut the electricity to the stove at the breaker box. We had to do that to keep the fire from spreading in the first place. We took 2 screws out and used the same screws to install the new bake element. It was just 2 connectors that had to be pulled apart gently from the old bake element. We plugged in the new bake element into the metal spaces where the old one came out. Replaced the screws and we were done. It was very easy.
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!
I had repair men replace the door hinges 2times and decided the 3rd time to do it myself and save some $. ordering was a chinch, received the parts in 2 days and followed instructions posted on this site. They were excellent. Just a few things I would stress: Lift UP the door to remove, not open the door fully and pull out and also make sure to take the small pins out of the new hinges before closing. They are so small you could over look them. The person who put detailed instructions on this site is to be commended for clarity and detail on "How To" I really appreciated it.