WU882 Maytag Dishwasher - Instructions

After removing the cover to the motor assembly, I determined that the problem was that the old drive belt had broken. It probably was more than 20 years old. I originally thought that the size was no longer available because the old belt had stretched about two inches, but, after reading the repair stories on the PartsSelect Website, I decided to try the 25 3/8" belt. It worked great! After a few tries I was able to stretch the belt across the two pulleys without having to loosen anything. After applying the silicon grease, the dishwasher worked as good as new. The most difficult aspect of the job was having to work in such a small space. The most time-consuming part of the job was removing and then replacing the access cover, but the job overall was quite easy.

Removed the seal and replaced with new one. Job went very easy. Stop the leake. Thank you.

Claude Miller

I removed four philips screws to remove the front door panel. Next I removed the screws holding in the detergent cup. Removed the two electrical wires from the cup release. Reveresed the process to install the new detergent cup.

Replaced whole assembly

Read thru the comments by others and matched them up with what I found (belt off the pulleys) when I took off the kickplate below the door. The old belt (20 years) had stretched about 1 1/2" compaired to the new replacement. Slip the new belt on the motor pulley and start it around the back of the pump pulley. Get your wife to hold your legs down so you can really twist/pull the pump pulley until the belt finally slips into place. No need to loosen the motor mounts if your wife can hold you down.

Firstly, I'm a 58 year old female and this repair was relatively easy for me, thanks to all the marvelous instructions on this site from others who made this same repair. Like the others, I removed the four lower screws on the INSIDE of the door along either outer edge. Before that, in error, I removed the four screws along the very bottom of the door, big mistake, hard to get them back in correctly. Removed the door panel and took out the 6 nuts from the dispenser cup, slipped the electrical clip thingys from the posts by slightly wiggling them straigt off, remember which color goes where. Cleaned the area around the old gasket and reattached the new gasket and dispenser cup. This was a little tricky holding it in place from the inside while using the nut drive on the outside. Whew! That was the hardest part for me. Thanks to all for the previous detailed instructions. I now have really clean dishes! Yay! Great feeling of accomplishment.

Changed springs on both sides as long as I was at it. Did this without having to pull out built in washer. Lock the door closed to give the least tension on the springs. Remove kick plate at bottom of washer. Remove small access panels on each side. If you have small enough paws you can reach thru the access holes and strectch the spring with your fingers to remove and install new springs or use needle nose pliers if you have to. Don't forget the nylon bushings that come with the springs or the metal on metal contact will eventually nick the springs hook and make them break . Hook top end of spring first (rounded hook) and then stretch spring by grasping between thumb and index finger and hook into bottom hole. Hardest part is having to lay on your stomach to do it. Reassemble and count the money you've saved.

it was very easy to unscrew the broken nozzle and screw back the new one. !

First removed the four screws to the lower front outside panel (the only tools needed to complete this job). Slide the belt under the drive motor, onto the motor pulley grove, then strecthed the belt onto the pulley for the pump that's on the power module (was qiite difficult, but with the directions supplied with the belt, was able to get it on) Lubricated the belt with silicon grease.

removed retaining nut and replaced

I removed the access panel and it was right there. one screw - disconect the wires & it was out. then right back in - access panel on, and done.

I removed the 4 lower Phillips head screws on the lower inside of the door.(thanks to a tip from Robert) This removed the front panel allowing access to the detergent cup. I removed the 6 screws holding the detergent cup. Removed the old detergent cup and gasket. Installed the new cup and gasket and reinstalled the front panel. Amazingly easy. Now it's on to my stove. I'm hooked on your website

Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.

replaced gasket.Didn't fix leaking water problem.I believed that there was too much water in washer, when the problem occurred.Found that the float had soap build up in it making it too heavy,letting in more water than the washer can handle.Cleaned build up from float and problem seems to have disappeared.

Removed the front covers on the bottom of the dish washer. I found it extremely difficult to stretch the belt over the second pulley so I soaked the belt in hot water for a few minutes to soften it. After I soaked the belt it stretched enough for me to work it into both pulleys. Don't forget to apply the grease (supplied with the belt) after the belt is installed.