WU601 Maytag Dishwasher - Instructions

Removed front panel by removing four screws. Used 5/16 nut driver to remove six screws holding dispenser and disconnected two wires. Inserted new dispenser and reattached cover. Longest time taken was to realign cover properly. Best approach seemed to install with door as near vertical as possible and to start screws by hand. ONLY FOUR screws hold the panel in place. Very easy repair for anyone. part arrived sooner than expected.

removed screws that secured cover plates. discovered that belt was broken. ordered new belt. ordered friday; delivered monday. read some previous repair experiences.

the trick to getting belt onto the pulleys is to first wrap it around the spindle part. then set the belt into the motor pulley groove. carefully start working the belt in the other pulley into the groove while rotating both pulleys. i had to lay on my stomach on the floor to do this, but it did not take very long. once the belt is in place, lubricate it with the included gel. took about 20 minutes with some trial and error.

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.

replaced belt....great service!!

lostened motor mounts,
streched belt across pulleys,
thghtened motor tension
replaced access panel.

Remove lower cover plate below door. Remove broken spring with needle nose pliers. Place plastic insert into upper spring loop and loop into hole on right spring hinge. Grab lower spring loop with needle nose pliers and insert through hole in lower frame base. Reinstall lower cover plate.

it was very easy to unscrew the broken nozzle and screw back the new one. !

First removed the four screws to the lower front outside panel (the only tools needed to complete this job). Slide the belt under the drive motor, onto the motor pulley grove, then strecthed the belt onto the pulley for the pump that's on the power module (was qiite difficult, but with the directions supplied with the belt, was able to get it on) Lubricated the belt with silicon grease.

Read thru the comments by others and matched them up with what I found (belt off the pulleys) when I took off the kickplate below the door. The old belt (20 years) had stretched about 1 1/2" compaired to the new replacement. Slip the new belt on the motor pulley and start it around the back of the pump pulley. Get your wife to hold your legs down so you can really twist/pull the pump pulley until the belt finally slips into place. No need to loosen the motor mounts if your wife can hold you down.

Firstly, I'm a 58 year old female and this repair was relatively easy for me, thanks to all the marvelous instructions on this site from others who made this same repair. Like the others, I removed the four lower screws on the INSIDE of the door along either outer edge. Before that, in error, I removed the four screws along the very bottom of the door, big mistake, hard to get them back in correctly. Removed the door panel and took out the 6 nuts from the dispenser cup, slipped the electrical clip thingys from the posts by slightly wiggling them straigt off, remember which color goes where. Cleaned the area around the old gasket and reattached the new gasket and dispenser cup. This was a little tricky holding it in place from the inside while using the nut drive on the outside. Whew! That was the hardest part for me. Thanks to all for the previous detailed instructions. I now have really clean dishes! Yay! Great feeling of accomplishment.

Replaced whole assembly

Changed springs on both sides as long as I was at it. Did this without having to pull out built in washer. Lock the door closed to give the least tension on the springs. Remove kick plate at bottom of washer. Remove small access panels on each side. If you have small enough paws you can reach thru the access holes and strectch the spring with your fingers to remove and install new springs or use needle nose pliers if you have to. Don't forget the nylon bushings that come with the springs or the metal on metal contact will eventually nick the springs hook and make them break . Hook top end of spring first (rounded hook) and then stretch spring by grasping between thumb and index finger and hook into bottom hole. Hardest part is having to lay on your stomach to do it. Reassemble and count the money you've saved.

had to remove the iner door plate and remove the main switch or latch to get to the micro switches witch one had over heated over time,it is working like new at this time.

This dishwasher is over 20 years old and still works well. The door springs broke and the skematic shows 2 springs on each side. The spring kit only includes one spring for each side which is the primary spring. Removed the bottom access panel, shut off the water line and removed the water line. Removed the top screws which lock the dishwasher in the cabinet and pulled forward about 6 inches to fully expose the springs. Replaced the two big springs, one on each side and adjusted for maximum pull of door. The second small springs were not necessary. Pushed unit back into the cabinet, connected the water line and tested for water leaks. Cleaned and replaced access panel and the door is light as a feather.

I removed four philips screws to remove the front door panel. Next I removed the screws holding in the detergent cup. Removed the two electrical wires from the cup release. Reveresed the process to install the new detergent cup.